User manual PANASONIC WV-CP240

[. . . ] WARNING: This apparatus must be earthed. IMPORTANT The wires in this mains lead are coloured in accordance with the following code. Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. [. . . ] Use lens tissue or a cotton tipped applicator and ethanol. Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused. Do not operate the camera beyond the specified temperature, humidity or power source ratings. Use the camera under conditions where temperature is between ­10°C - +50°C (14°F 122°F), and humidity is below 90 %. The input power source is 220 V - 240 V AC 50 Hz for WV-CP240, 12 V DC for WV-CP242, and 24 V AC 50 Hz for WV-CP244. MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS <WV-CP240> ALC BLC ON VIDEO SHARP INT VIDEO OUT DC ELC SOFT OFF LL ALC BLC ON VIDEO SHARP INT LOCK <WV-CP244> AC 24V IN GND DC ELC SOFT OFF LL WV­CP244 1 2 ALC BLC ON VIDEO SHARP INT VIDEO OUT DC ELC SOFT OFF LL <WV-CP242> DC 12V IN ALC BLC ON VIDEO SHARP ALC BLC ON VIDEO SHARP DC VIDEO OUT DC ELC SOFT OFF ELC SOFT Camera mounting screw holes OFF Fixing screws Mount adapter q Auto Iris Lens Connector Supplies power and control signals to an auto iris lens (not supplied). w Flange-back Adjusting Ring This ring adjusts the back-focal distance or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CSmount lens. e Lens (option) r Mount Adapter The camera mounting screw hole is for mounting the camera onto a mounting bracket. The camera is originally designed to be mounted from the bottom, however, a topmounting type is also available. To mount from the top, remove the mount adapter from the bottom of the camera by removing two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket. Make sure that two original screws are used when mounting the mount adapter; longer type screws may damage inner components, too shorter type screws may cause the camera drop. t Focus Fixing Screw y Power Cord (only for WV-CP240) Connect this power cord to an electrical outlet of 220 V - 240 V AC 50 Hz. u DC 12 V Input Terminal [DC 12V IN (only for WV-CP242)] This terminal is for connecting the 12 V DC power supply cord. i AC 24 V Input Terminal [AC 24V IN (only for WV-CP244)] This terminal is for connecting the 24 V AC 50 Hz power supply cord. o Synchronization Mode Selector [INT, LL (only for WV-CP240 and WVCP244)] Selects the camera synchronization mode as either internal sync mode (INT) or line-lock mode (LL). !0 Back Light Compensation Mode Selector (BLC ON, OFF) Lets you select the mode according to the position of the object and light conditions on the screen. [. . . ] q Mount the lens by turning it clockwise on the lens mount of the camera. w Connect the lens cable to the auto iris lens connector on the side of the camera. 10. 5V DC VA - (R x 0. 42 x L) 16V DC L : Cable length (m) R : Resistance of copper wire (/m) VA : DC output voltage of power supply unit L standard = L minimum = L maximum = VA - 12 0. 42 x R VA - 16 0. 42 x R VA - 10. 5 0. 42 x R (meters) (meters) (meters) Focus fixing screw C. WV-CP244 (24 V AC 50 Hz) cs Connect the power cable to the AC 24 V IN terminal on the rear panel of the WV-CP244. [. . . ]