User manual PANASONIC WV-CP464

[. . . ] Color CCTV Cameras Operating Instructions Model No. WV-CP460 WV-CP464 (Lens Option) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. N0100-1020 YWV8QA5377BN Printed in Japan N 19 For U. S. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] (When the cursor is moved on an area that has already been masked, the mask and cursor start blinking. ) Blinking 4. To cancel masking, move the cursor to that area and press . After masking is completed, press for 2 seconds or more. If you want to change the video output level (picture contrast), move the "I" cursor for LEVEL and adjust the level. Turns to white Blinking Note: If ON is selected for the SUPER-D2 parameter, a shadow (black line) may appear at the boundary between the bright and the dim scene. This is a natural phenomenon and does not indicate trouble. 3. Shutter Speed Setting (SHUTTER) Note: When ELC is selected for ALC/ELC on the CAM SET UP menu or ON is selected for SUPER-D2 on the ALC CONT menu, this item is not available. To select electronic shutter speed, select OFF for SUPER-D2 in the ALC CONT menu. Move the cursor to the SHUTTER parameter and select the electronic shutter speed. The preset values for SHUTTER (electronic shutter speed) change by pressing as shown at below: OFF (1/60) 1/10000 1/100 1/4000 1/250 1/2000 1/500 1/1000 or 4. Gain Control Setting (AGC ON/OFF) You can set the gain (brightness level portion of an image) to automatic level adjustment (ON) or fixed level (OFF). Move the cursor to the AGC parameter and select automatic level adjustment (ON) or fixed level (OFF). Note: If ON is selected for the AGC parameter, the noise reduction function is automatically activated under low light conditions to reduce noise. In pictures containing a moving object, this may result in an afterimage. 5. Electronic Sensitivity Enhancement (SENS UP) There are two modes for SENS UP. AUTO: If you select X10 AUTO, for example, the sensitivity is raised automatically to X10 max. When AUTO is selected, AGC is automatically set to ON. FIX: If you select X32 FIX, for example, the sensitivity is raised to just X32. Move the cursor to the SENS UP parameter and select the parameter for electronic sensitivity enhancement. The preset values for SENS UP (electronic sensitivity enhancement) change by pressing or as shown right: OFF X32 FIX X2 AUTO X16 FIX X4 AUTO X10 FIX X6 AUTO X6 FIX X10 AUTO X4 FIX X2 FIX OFF Notes: · When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this item. · When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has priority so that the SUPER-D2 function is not activated automatically. · While the SENS UP function is selected, noise, spots or a whitish phenomenon may appear in the picture when the sensitivity of the camera is increased. Synchronization Setting (SYNC) You can select internal sync mode (INT) or line-lock mode (LL). [. . . ] Move the cursor to the LENS DRIVE parameter. Select DC if you are using the auto iris lens that requires a DC drive signal. Select VIDEO if you are using the auto iris lens that requires a video drive signal. 10. Special Menu This menu lets you adjust and setup the video signal of the camera to meet your requirements. [. . . ]