User manual PANASONIC WV-CP474

[. . . ] (1) Auto Light Control (ALC)/Electronic Light Control (ELC) (2) The SUPER-D2 function eliminates interference by strong background lighting which makes the camera picture dark, such as a spotlight. (3) Internal Line-locked Multiplex Vertical (VD2) Sync. (4) Auto/Manual White Balance Function (5) Electronic Shutter Function 2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off) 3. [. . . ] Move the cursor to END, then to the item(s) you want to change. ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER --AGC ON(DNR-H) SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF LENS DRIVE DC END SET UP DISABLE ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER --AGC ON(DNR-H) SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF LENS DRIVE DC END SET UP ENABLE 2-1. ALC Mode with SUPER-D2 ON Super Dynamic2 Function (SUPER-D2) The important object in a scene is usually placed in the center of the monitor screen. In the SUPER-D2 mode, more photometric weight is given to the center of the screen (where the important object is located) than to the edge of the screen (where a bright backlight would most likely be located). You can use the SUPER-D2 function if you select ALC. It eliminates interference by strong background lighting which makes the camera picture dark, such as a spotlight. Move the cursor to SUPER-D2 and select ON. Important Notice: When the setup menu is closed after changing the parameters in the menu, the new values are stored in the EEPROM (Electrically Erasable and Programmable Read-Only Memory). These values remain valid until new values are stored, even if the power of the camera is off. ** ALC CONT ** BACK LIGHT COMP SUPER-D2 ON LEVEL RET END . . . I. . . . . If you want to adjust the video output level, move the "I" cursor for LEVEL. Adjust to the desired level by pressing L or R. (To be continued reverse page) SETTING PROCEDURES 2-2. ALC Mode with SUPER-D2 OFF and ELC Mode Note: If ELC is selected, set MASK SET according to this procedure. Move the cursor to SUPER-D2 and select OFF. (When you select ELC, SUPER-D2 is not available. ) The MASK SET appears on the menu. 6. Synchronization Setting (SYNC) You can select internal sync (INT) mode, line-lock (LL) mode or the VD2 signal (multiplexed vertical drive signal) mode. ** ALC CONT ** BACK LIGHT COMP SUPER-D2 MASK SET LEVEL OFF . . . I. . . . . Move the cursor to SYNC and select LL or INT. If LL is selected, the SYNC menu appears. (If VD2 or INT is not selected, the synchronization mode automatically set and the menu does not appear. ) Important Notices: 1. The priority for the sync modes is as follows: (1) Multiplexed Vertical Drive (VD2) (Highest priority) (2) Line-lock (LL) (3) Internal Sync (INT) (Lowest priority) 2. The line-lock mode has a submenu for line-lock vertical phase adjustment. If the camera installation is relocated, check the vertical phase adjustment again since the AC line phase may be different. Whenever the multiplexed vertical drive pulse (VD2) is supplied to the camera from external equipment such as a matrix switcher, the camera sync mode is automatically switched to the VD2 mode. 2. Move the cursor to MASK SET and press SET. The 48 mask areas appear on the monitor screen. [. . . ] Notes: · We recommend that you usually select ON. · When the camera is used to synchronize the system for external sync, select ON to prevent a malfunction. To reset to the factory settings (CAMERA RESET) 1. While holding down L end R, press SET for 2 seconds or more. The camera is reset to the factory settings. 9. [. . . ]