User manual PANASONIC WV-CPR654

[. . . ] Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framstölls i Direktiv 73/23/EEC och 89/336/EEC. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ia 89/336/EEC. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som fælger bestemmelsene i direktiven 73/23/EEC og 89/336/EEC. For Australia THIS APPARATUS MUST BE EARTHED. To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. [. . . ] AUX1: Turn off the Shift Switch to select this position. AUX2: Turn on the Shift Switch to select this position. Housing Switch (HOUSING: WIPER / DEF) Used to control the wiper or defroster of the housing. WIPER: Turn on the Shift Switch to select this position. DEF: Turn off the Shift Switch to select this position. Up Switch (2) This switch is used to move the cursor (on the program or camera menu) in the up direction. Right Switch (6) This switch is used to move the cursor (on the Set up or Program Menu) in the right direction. Set Switch (5) The mode selected in the program or camera setup menu is enabled by pressing this switch. 15. Down Switch (8) This switch is used to move the cursor (on the Set up or Program Menu) in the down direction. Left Switch (4) This switch is used to move the cursor (on the Set up or Program Menu) in the left direction. Position Switch (POSI) Used to turn the pan/tilt head to the preset position. Random Panning (Only WV-RC100 or WV-RC150 connection) 3-1. The LED of the RANDOM will light and automatic panning will start. SHIFT LED lights off SHIFT PAN RANDOM AUTO LED lights on LED lights on PAN RANDOM AUTO LED lights on 2-2. To stop this panning, press the PAN Switch again. The panning will stop and the LED of AUTO will light off. 3-3. To stop this panning, press PAN Switch again. The panning will stop and the LED of RANDOM will light off. -8- 4. The camera is turned to the preset position. SHIFT LED lights on CLOSE TELE IRIS ZOOM OPEN WIDE 1 4 7 HOME 2 5 SET 3 To brighten 6 9 POSI To darken 8 0 1 2 Note: The control speed may be slow during the AGC setting in the camera side. c. Home Position Setting Press the HOME Switch. The camera is turned to the preset home position. Allows the iris level to return into the initial one. Press the OPEN and CLOSE switches simultaneously more than 1 sec. The iris level is reset to the preset one. SHIFT 1 4 7 HOME 2 5 SET 3 6 9 LED lights on. 8 0 CLOSE POSI TELE IRIS ZOOM OPEN WIDE 1 Press both switches simultaneously for 1 second or more. Note: When the camera is not operated for a certain time (preset time) in the AUTO HOME POSI or SELF RETURN On mode, it moves to the home position automatically. d. [. . . ] When the up load has been done to the changed camera, the camera picture may not be same with the previous one. Set the camera condition with the Camera Set Up Menu again. The all preset data should be erased due to the up load operation. Return · Error Display When an error occurs during Up/Down Loading, the following messages are displayed on the monitor. Message Error 1 Cause Incompatibility of model Note A difference between the transmission information and the model occurs during up/down loading. The transmission information is over the capacity in memory during down loading. [. . . ]