User manual PANASONIC WV-CS600

[. . . ] Combination Camera WV-BS500 WV-BS504E WV-BST500 WV-CS600A WV-CS604E WV-CSR600 WV-CST600 Before attempting to connect or operate this product, please read these instructions completely ENGLISH VERSION For Australia THIS APPARATUS MUST BE EARTHED. To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Wrongly wired extension cords are a major cause of fatalities. [. . . ] Modes change as follows: OFF SEQ SORT AUTO PAN *** SET UP MENU *** PRESET 1* MAP* HOME POSITION SELF RETURN AUTO MODE LOCAL/REMOTE CAMERA * 15 10MIN AUTO PAN* LOCAL AUTO PAN setting menu 2. When AUTO PAN is selected, set details as follows: Move the cursor to AUTO PAN* and press the CAM (SET) key to display the AUTO PAN setting menu. ** AUTO PAN ** POSITION SET SPEED ENDLESS DWELL TIME RET START END . . . I. . . . To set a panning start position and panning end position Follow the steps below. (1) Move the cursor to POSITION SET and press the CAM (SET) key. (2) Move the joystick to the left or right to select a panning start position and press the CAM (SET) key. This determines the start position and the cursor moves to END. (3) Move the joystick to the left or right to select a panning end position and press the CAM (SET) key. This determines the end position and the cursor moves to POSITION SET. ** AUTO PAN ** POSITION SET SPEED ENDLESS DWELL TIME RET START END . . . I. . . . L H ON 2S ** AUTO PAN ** POSITION SET SPEED ENDLESS DWELL TIME RET START END . . . I. . . . To set a panning speed Move the cursor to SPEED, and move the joystick to the left or right to set a panning speed. The panning speed increases when the joystick is moved to the right, and decreases when it is moved to the left. ** AUTO PAN ** POSITION SPEED ENDLESS DWELL TIME RET START END . . . I. . . . To set endless turn ON/OFF Move the cursor to ENDLESS, and move the joystick to the left or right to set endless turn ON or OFF. ON: The camera pans from the start position to the end position, then keeps rotating in the same direction to return to the start position. OFF: The camera pans from the start position to the end position, then rotates backward to the start position. This movement is repeated over and over. To set a dwell time move the cursor to DWELL TIME and select a dwell time by moving the joystick to the left or right. Dwell time changes as follows: ** AUTO PAN ** POSITION SPEED ENDLESS DWELL TIME RET START END . . . I. . . . L H ON 2S ** AUTO PAN ** POSITION SPEED ENDLESS DWELL TIME RET START END . . . I. . . . L H ON 2S 1S 4MIN 2S 3S 5S 2MIN 10S 30S 1MIN Note: When the panning, tilting, lens zoom or focus operation is controlled manually, the Auto mode function should be canceled. To activate Auto mode, select AUTO MODE ON again. s LOCAL/REMOTE Setting · Move the cursor to LOCAL/REMOTE, and move the joystick to the left or right. You can toggle between LOCAL and REMOTE. Note: REMOTE does not work when the WV-RM70 is connected. [. . . ] Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry seal until it has been ascertained that the unit is functioning. CONNECT THIS TO 24V AC CLASS 2 POWER SUPPLY ONLY. To prevent fire or electric shock hazard, the UL listed wire (VW-1, style 1007) should be used for the cable for 24V AC input terminals. - 33 - · RS485 site connection Brown GND Red Data Transmission Orange Yellow Data Reception Green T (B) T (A) R (B) R (A) For daisy chain connection of multiple cameras, make sure to match each male connector with its female counterpart. [. . . ]