User manual PANASONIC WV-CS650

[. . . ] Combination Camera WV-CS650 WV-CS654 WV-CSR650 Before attempting to connect or operate this product, please read these instructions completely ESPAÑOL FRANÇAIS DEUTSCH ENGLISH ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive CEE/73/23 e CEE/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med den følgende standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC. [. . . ] Note: Your selected preset number is canceled only in SEQ and SORT mode. The previously set parameters (for PAN, TILT positions, etc. ) are not changed. If you wish to change these parameters, you must set them again. PRESET NUMBER SET menu * PRESET NUMBER SET * 1* 5* 9* 13* 17 21 25 29 ID: 33-64 2* 6* 10* 14* 18 22 26 30 RET 3* 7* 11* 15 19 23 27 31 4* 8* 12* 16 20* 24 28 32 s Home Position Setting 1. To set a position number for the home position Move the cursor to HOME POSITION and select the desired position number by moving the joystick to the left or right. Select OFF if you are not using the home position function. Setup menu *** SET UP MENU *** PRESET 1* MAP HOME POSITION SELF RETURN AUTO MODE FLIP-A-CHIP LOCAL/REMOTE CAMERA 15 10MIN AUTO PAN ON LOCAL s Self Return Setting · To set a time-out parameter for return to the home position Move the cursor to SELF RETURN and select a return time by moving the joystick to the left or right. Return time changes as follows: 1MIN OFF 2MIN 3MIN 5MIN 10MIN 20MIN Setup menu *** SET UP MENU *** PRESET 1* MAP HOME POSITION SELF RETURN AUTO MODE FLIP-A-CHIP LOCAL/REMOTE CAMERA 15 10MIN AUTO PAN ON LOCAL 60MIN 30MIN MIN signifies minute(s). - 17 - s Auto Mode Setting 1. To set auto mode Move the cursor to AUTO MODE and select a mode by moving the joystick to the left or right. Modes change as follows: OFF SEQ SORT AUTO PAN Setup menu *** SET UP MENU *** PRESET 1* MAP HOME POSITION SELF RETURN AUTO MODE FLIP-A-CHIP LOCAL/REMOTE CAMERA 15 10MIN AUTO PAN ON LOCAL 2. When AUTO PAN is selected, set details as follows: Move the cursor to AUTO PAN and press the CAM (SET) key to display the AUTO PAN setting menu. AUTO PAN setting menu ** AUTO PAN ** POSITION SET SPEED ENDLESS DWELL TIME RET START END . . . I. . . . To set a panning start position and panning end position Follow the steps below. (1) Move the cursor to POSITION SET and press the CAM (SET) key. (2) Move the joystick to the left or right to select a panning start position and press the CAM (SET) key. This determines the start position and the cursor moves to END. (3) Move the joystick to the left or right to select a panning end position and press the CAM (SET) key. This determines the end position and the cursor moves to POSITION SET. ** AUTO PAN ** POSITION SET SPEED ENDLESS DWELL TIME RET START END . . . I. . . . L H ON 1S ** AUTO PAN ** POSITION SET SPEED ENDLESS DWELL TIME RET START END . . . I. . . . To set a panning speed Move the cursor to SPEED, and move the joystick to the left or right to set a panning speed. The panning speed increases when the joystick is moved to the right, and decreases when it is moved to the left. Caution: If the panning range is changed after the camera has not panned for a long time or has been panning in the same panning range, the picture may not be clear or noise may appear. If this is the case, pan the camera fully several times. If this does not eliminate the problem, refer servicing to qualified service personnel. ** AUTO PAN ** POSITION SET SPEED ENDLESS DWELL TIME RET START END . . . I. . . . To set endless turn ON/OFF Move the cursor to ENDLESS, and move the joystick to the left or right to set endless turn ON or OFF. [. . . ] After clamping the contacts, push them into the proper holes in the accessory connector of this camera until they snap in place. Up Up Wire Wire 4 2 3 1 Contact Contact How to assemble the cable with the accessory connector Strip back the cable jacket approx. 3 mm (0. 1 inch) and separate the individual conductors. Approx. 3 mm (0. 1 inch) 0. 1 inch Up A Contact Contact Insert Insert Wire Wire CAUTION Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry seal until it has been ascertained that the unit is functioning. [. . . ]