User manual PANASONIC WV-CSR604

[. . . ] Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de bepalingen van Richtlijnen 73/23/ EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med den følgende standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/ EEC og 89/336/EEC. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The serial number of this product may be found on the top of the unit. [. . . ] · When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has priority so that the SUPER-D2 function is not activated automatically. · While the SENS UP function is selected, noise, spots or a whitish phenomenon may appear in the picture when the sensitivity of the camera is increased. Synchronization Setting (SYNC) Select one of the three sync source modes. (1) Multiplexed Vertical Drive (VD2) (Highest priority) (2) Line-lock (LL) (3) Internal Sync (INT) (Lowest priority) 6-1. Line-lock Sync Mode (LL) The line-lock mode has a submenu for line-lock vertical phase adjustment. If the camera installation is relocated, check the vertical phase adjustment again since the AC line phase may be different. ** SYNC ** Note: The settings in this menu can be V PHASE made only when the multiplexed COARSE 1(1--16) vertical drive signal (VD2) is not FINE I. . . . . . . . After confirming that the cursor is on LL, press I(S). The vertical phase adjustRET END ment menu appears on the monitor screen. Supply the video output signal of the camera to be adjusted and the reference camera video output signal to a dual-trace oscilloscope. Set the oscilloscope to the vertical rate and expand the vertical sync portion on the oscilloscope. Move the cursor to WHITE BAL and select AWC PUSH SW. Press I(S) to start the white balance setup. The PUSH SW is highlighted to indicate that the white balance is being set. ** CAM SET UP ** CAMERA ID OFF ALC ALC SHUTTER --AGC ON(DNR-H) SENS UP OFF SYNC INT WHITE BAL AWCPUSH SW MOTION DET OFF MENU END SET UP ENABLE Highlighted 3. When the white balance setting is completed, the PUSH SW returns to normal display. Note: If white balance is not set, the PUSH SW is being highlighted. When you want to adjust the white balance manually, press I(R) to select AWC and press I(S). The AWC menu appears on the monitor screen. (When ATW1 or ATW2 is selected, pressing I(S) displays the ATW1 or ATW2 menu. ) ** R B MASK SET AWC ** . . . . I. . . . Manual Fine Adjustment for AWC (ATW1/ATW2) You can set the white balance items manually. To set MASK SET, proceed as described in steps 2 to 4 of "ALC mode with SUPER-D2 OFF". Press I(L) or I(R) to obtain the optimum amount of red gain. [. . . ] a) Screw-holes, cable access holes, and gaps: Fill these portions with silicon rubber or equivalent waterproofing material. b) Cable joints: · Use tape with electrical insulation and waterproof characteristics. · Tape separately the three leads of the power cords, and cover the joint portions. · Tape the joint portion of the video cables. 8. [. . . ]