User manual PANASONIC WV-CU161C

[. . . ] System Controller Operating Instructions Model No. WV-CU161C OP ER ATE SH RE SE T SUS PEN D IFT ALA RM RM ALA 1 SE CA SETMERA UP TU P M 2 4 3 5 8 6 9 WIP AUX 1 AU B/W PAT ER TO PATR PLA OL Y Sys SLO FUCAMER NCT A ION W PRO GRA 7 HO ME tem Co RO ntr olle LS rW TOP V-C U C PAT DE F RO L LE ARN ES C 0 SE T PR PR OGR ES AM ET NE PR AR FO CU AUX 2 ES ET AUT E ZO UP L S FAR WID CLO OF OC US E SE IRIS IRIS RE SE O T PEN OM TEL R DO WN Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ENGLISH VERSION Caution: Before attempting to connect or operate this product, please read the label on the bottom. For U. S. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Move the joystick to the right or left to select the desired preset numbers of the picture on the monitor in the range from 1-64 or [­] if no preset numbers are assigned. The initial factory setting is ­ (No assignment). 1-64: Preset numbers ­: No assignment Note: ALARM PRESET is only available when a combination camera is connected. 4. Select the alarm terminal number by moving the joystick up or down. Move the joystick to the right or left to select the desired preset numbers. The initial factory setting is ­ (No assignment). 1-64: Preset numbers ­: No assignment 6. Press the HOME/ESC button to return to the previous menu. Notes: · ALARM TERMINAL is only available when a combination camera is connected. · If the camera has the Preset Alarm ON/OFF mode, then set it to OFF. 21 s System Setup 1. Select SYSTEM SETUP by moving the joystick up or down. Press the PRESET/SET/PROGRAM PRESET button. The SYSTEM SETUP menu appears on the monitor. s Preset Data Loading The data settings preset to the camera are downloaded to the controller. A set of preset data can be given a title by the controller operation. The preset data with the title can be uploaded to other cameras. Select PRESET DATA LOAD by moving the joystick up or down. Press the PRESET/SET/PROGRAM PRESET button. The PRESET DATA LOAD screen appears on the monitor as shown below. SYSTEM SETUP CABLE COMP S SWITCH BUZZER ON PRESET DATA LOAD CAM1: CAM2: CAM3: CAM4: CAM5: CAM6: CAM7: CAM8: Cable Compensation Setting This item lets you select a compensation level to match to transmission loss caused by cable extension. Select CABLE COMP by moving the joystick up or down. Select the most appropriate cable length by moving the joystick to the right or left. S: Less than 400 m (1 300 ft) M: 400 m (1 300 ft) to 700 m (2 300 ft) L: 700 m (2 300 ft) to 900 m (3 000 ft) (When using RG-59U, BELDEN 9259 or equivalent cable) P : Data saved. (The factory default setting for all cameras from CAM1 to CAM8 is s. ) Downloading 1. [. . . ] One is to use the setup menu and the other is to operate the camera. Follow the procedures described below to set the camera patrol learning up while operating the combination camera. Press the PATROL LEARN button while holding down the PROGRAM button. CAMERA SETUP q Camera Preset Position There are two ways of presetting camera positions. One is to use the setup menu of the combination camera and the other is to operate the camera. [. . . ]