User manual PANASONIC WV-CU550B

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example use only shielded interface cables when connecting to computer or peripheral devices). [. . . ] When the dirt is hard to remove, use a mild detergent and wipe gently. · Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Use the appliance at temperatures within ­10°C +50°C (14°F - 122°F) and a humidity below 90 %. The input power source for this appliance is 120 V AC 60 Hz. 4 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS s Front View q w e r t ALARM BUSY !8 !9 ACK RESET BACK FORWARD SEQ SEQ ALT F1 F2 F3 F4 UP 1 4 2 5 8 3 6 PRESET IRIS CLOSE OPEN LEFT RIGHT @1 @0 AUX 1 2 DEC INC ­1CAM +1CAM STOP y AF 7 MON 9 CAM SET ZOOM TELE FOCUS NEAR DOWN 0 SLOW ESC WIDE FAR System Controller WV-CU 550B !7 !6 !5 !4 !3 !2 !1 !0 o i u s Rear View DATA IN OUT TERM ON OFF CONTROLLER UNIT NO. MODE 1-8 901 CONTROLLER ON OFF 23 #1 #2 #3 5 456 78 #4 #5 #6 q Alarm Indicator (ALARM) Blinks to indicate that an alarm condition exists. It changes to steady light when the alarm is reset automatically. To turn the indicator off, press the ACK RESET button. w Busy Indicator (BUSY) Lights up when you attempt to control a monitor or a camera that is already used by a higher priority operator, or when the higher priority operator selects the monitor or camera you are currently operating. Operations from the System Controller are disabled until this indicator goes off. e Function Buttons (F1/F2/F3/F4) Select functions displayed on the LCD (Liquid Crystal Display) display. r LCD (Liquid Crystal Display) Display Displays function menus, numeric input, and system status. t Direction Buttons (4, 5, i, o) Select a function menu for display on the LCD display. y Joystick Controller (UP/DOWN/LEFT/RIGHT) The joystick is used to manually operate the Pan/Tilt Head, or move the cursor in the Matrix Switcher's Setup Menu on the active monitor screen. To control the Pan/Tilt functions of the Combination Camera slowers, press the ALT button (ALT indicator lights) before operating the joystick. u Iris Control Buttons (IRIS CLOSE, OPEN) Close or open the lens iris of cameras equipped with the specified lens. When these buttons are pressed at the sometime for 3 seconds or more, the lens iris is reset to the factory default setting. i Focus Control (FOCUS NEAR/FAR) Adjust the lens focus of cameras equipped with the specified lens. o Zoom Control (ZOOM TELE/WIDE) This control is used for zooming cameras equipped with the specified lens. !0 Preset Button (PRESET) Auto Focus Button (AF) PRESET: This button, in combination with the Numeric keys, is used to move the selected camera to a preset position in a system equipped with the specified cameras. AF: Pressing this button will automatically set the lens focus of a specified camera such as the WV-CS854. !1 Camera (Set) Key [CAM (SET)] CAM: Used for camera selection. [. . . ] WJ-AD550 Video Input Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WV-PB5508 Video Output Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WV-PB5504A Alarm Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WV-PB5564 Data Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]