User manual PANASONIC WV-CU550CJ

[. . . ] 11 Caution: Before attempting to connect or operate this product, please read the label on the bottom. For U. S. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Moisture may damage the appliance and also cause electric shock. · Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently. · Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Use the appliance at temperatures within ­10 °C to +50 °C (14 °F to 122 °F) and a humidity below 90 %. The input power source for this appliance is 120 V AC 60 Hz. 5 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Front View q w e r t ALARM BUSY y u @0 @1 @3 @2 F1 F2 F3 F4 ACK RESET BACK FORWARD SEQ SEQ ALT 1 4 2 5 8 0 3 6 PRESET IRIS CLOSE OPEN AF AUX 1 2 DEC INC -1CAM +1CAM STOP 7 MON 9 CAM SET ZOOM TELE FOCUS NEAR SLOW ESC WIDE FAR System Controller WV-CU 550 CJ !9 !8 !7 !6 !5 !4 !3 !2 !1 !0 o i Rear View DATA IN OUT TERM. 1-8 78 901 CONTROLLER MODE ON OFF 23 @4 @5 @6 6 456 OFF @7 @8 @9 q Alarm Indicator (ALARM) Blinks to indicate that an alarm condition exists. It changes to steady light when the alarm is reset automatically. To turn the indicator off, press the ACK RESET button. w Busy Indicator (BUSY) Lights up when you attempt to control a monitor or a camera that is already used by a higher priority operator, or when the higher priority operator selects the monitor or camera you are currently operating. Operations from the System Controller are disabled until this indicator goes off. e Function Buttons (F1/F2/F3/F4) Select functions displayed on the LCD (Liquid Crystal Display) display. r LCD (Liquid Crystal Display) Display Displays function menus, numeric input, and system status. t Direction Buttons (A, B, D, C) Select a function menu for display on the LCD display. y Zoom Wheel Controller This control is used for zooming cameras equipped with the specified lens. Moving the control to the right will zoom in the image. Moving the control to the left will zoom out the image. u Joystick Controller (UP/DOWN/LEFT/RIGHT) The joystick is used to manually operate the Pan/Tilt Head, or move the cursor in the Matrix Switcher's Setup Menu on the active monitor screen. i Top Button Pressing this button will automatically set the lens focus of a specified camera. o Iris Control Buttons (IRIS CLOSE, OPEN) Close or open the lens iris of cameras equipped with the specified lens. When these buttons are pressed at the sometime for 3 seconds or more, the lens iris is reset to the factory default setting. [. . . ] WJ-SX550C Extension Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WJ-AD550 Video Input Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WV-PB5508 Video Output Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WV-PB5504A Alarm Input Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]