User manual PANASONIC WV-CW244F

[. . . ] This product should be installed and connected by qualified service personnel or system installers in conformity with NEC. Use a class 2 power source supplying 12 V DC or 24 V AC. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) to connect the power supply to the camera. Be sure to use a ceiling board/wall having enough strength to support this camera. [. . . ] Cable route Cables will go behind the junction box. Waterproof Process When necessary, apply waterproof process to the camera and relevant portions. Be sure to apply silicone rubber to the camera fixing screws in case of outdoor installation. Remove the two red-colored screws provided for transport protection using a Philips screwdriver. AP * Default setting FEATURES · Mounting method: Flash mounting/WVCW244F, Surface mounting/WV-CW244S · Signal processing: Automatic Light Control (ALC), Automatic Gain Control (AGC), Automatic Tracing White Balance (ATW), etc. · Synchronization: Internal, Line-Lock (only 24 V AC), and Multiplexed Vertical Drive (VD2) · Minimum illumination: 2. 4 lx (0. 24 foot-candle) at WIDE · Signal-to-noise ratio: 50 dB (Equivalent to AGC OFF) · Horizontal resolution: 480 TV lines · Optional heater unit available for the camera used at temperatures between ­10 °C and ­30 °C (14°F and ­22°F). q Focus lock lever Fixes the focus position after adjusting. w Tilting lock screw Fixes the tilting position after adjusting. e Zoom lock lever Fixes the zoom position after adjusting. r Panning table Adjusts the panning angle of the camera. t Azimuth adjuster Adjusts the azimuth angle to obtain a level image. y Pan lock screw Fixes the panning position after adjusting. u Heater power connector Supplies power to the optional heater unit when it is built in the camera. Connect here a harness sticking out from the heater unit. i Synchronization Mode Selector Specifies a source for synchronization. Note: Do not set the switch to LL (LineLock) position when supplying 12 V DC to avoid synchronization error. o Back Light Compensation Selector ON: Compensates the background if it is brighter than the object. !0 Aperture Level Selector SHARP: Sharpens the image outline. mini jack) For connecting an LCD monitor to adjust the camera images. Use an L-type plug to save space. 2nd transport protection screw 51 mm (2") ON 1 2 3 Heater unit installation See OPTIONAL HEATER UNIT for details. Adhesive tape Harness Fold Supplied screw Image Adjustment You can manually adjust the pan/tilt/azimuth angles, focus, and zoom while observing the connected monitor. Variable angles plus or minus 75 ° (max. ) SPECIFICATIONS Pick-up device: Scanning area: Scanning: Horizontal: Vertical: Synchronization: Video output: Horizontal resolution: Signal-to-noise ratio: Minimum illumination: 768 (H) x 494 (V) pixels, Interline transfer CCD 4. 8 (H) x 3. 6 (V) mm (Equivalent to 1/3" pick-up tube) 525 lines/60 fields/30 frames 15. 734 kHz 59. 94 Hz Internal, Line-lock (only 24 V AC), or Multiplexed vertical drive (VD2) 1. 0 V [P-P] NTSC composite 75 /BNC connector 480 lines 50 dB (Equivalent to AGC Off, weight On) 2. 4 lx (0. 24 footcandle) (WIDE), When the optional WV-CW2C dome cover is installed. 1. 0 lx (0. 1 footcandle) (WIDE), SHARP or SOFT, selectable ATW CS-mount 3. 8 mm - 8 mm 1:1. 4 (Wide), 1:1. 8 (Tele) Horizontal: 35. 6 ° - 73. 6 ° Vertical: 26. 6 ° - 53. 4 ° 1. 2 m - (3. 9 ft - ) ­10 °C - +50 °C (14 °F - 122 °F) ­30 °C - +50 °C (­22 °F - 122 °F) (When the optional heater unit built in) Less than 90 % 12 V DC, 265 mA (Camera) 24 V AC 60 Hz, 3. 0 W (Camera) 24 V AC 60 Hz, 12. 1 W (Heater unit) WV-CW244F: 133 mm (H) x 152. 5 mm (D) 5-1/4" (H) x 6" (D) WV-CW244S: 136. 5 mm (H) x 160 mm (D) 5-3/8" (H) x 6-5/16" (D) WV-CW244F: 1. 2 kg (2. 7 lbs. ) WV-CW244S: 1. 7 kg (3. 8 lbs. ) OPTIONAL HEATER UNIT Optional Heater Unit WV-CW3H Introduction Installing this heater unit enables the camera to operate under in a low-temperature environment of ­30°C (­22°F). The heater turns on automatically when the temperature inside the camera drops below +10°C (50°F) and turns off when it rises. A small fan inside the unit will minimize condensation on the surface of the dome cover caused by changes in ambient temperature unless temperatures change too rapidly. The fan will stop when there is no possibility of condensation. Point "A" (inside the wall) Pan lock screw (stainless) Precautions · This product should be installed and connected by qualified service personnel or system installers. · Do not use the same 24 V AC power source supplying the power to the camera for the heater unit. [. . . ] Power cord First, tape the individual wires, finally all of them as a whole. Power cord Wire Color Black White Green/Yellow 24 V AC 24 V AC (L) 24 V AC (N) Ground 12 V DC Positive Negative Not Used Resistance /ft 2. Connector junctions Tape the BNC-BNC junction point. Heater power cable 10. 5 V DC VA - 2(R x I x L) 16 V DC L : Cable length (m) (ft) R : Resistance of copper wire (/m) (/ft) VA : DC output voltage of power supply unit I : DC current consumption (A). See specifications. Video output cable 3. Gaps and holes Apply such a waterproof material as silicone clay (rubber) to the gaps, screws, holes, and other relevant portions. [. . . ]