User manual PANASONIC WV-CW374

[. . . ] Attach the camera mounting arm to the left or right hinges of adapter box, so that the mounting arm can be opened and closed flexibly. (Refer to the illustration in Step 4. ) I Waterproof Process Apply waterproofing to the necessary portions, using appropriate materials. This camera is applied to IP66 only when installed according to the instructions in this document, and appropriate waterproofing is applied. [. . . ] Remove the rear cover by loosening the fixing screw. 46 mm {1-13/16"} Hole 6 mm (W) x 10 mm (H) {1/4" (W) x 13/32" (H)} 83. 5mm {3-5/16"} I Precautions · Refer all work related to the installation of this product to qualified service personnel or system installers. · Do not operate the appliance beyond its specified temperature, humidity, or power source ratings. Use the camera at temperatures between ­30 °C and +50 °C {between ­22 °F and 122 °F}, and humidity below 90 %. The input power source for this appliance is 12 V DC/24V AC 60 Hz for WV-CW374. When you install the camera in a low-temperature location and start operating it, it may take time (around 30 minutes) for the inside of the camera to warm up. · Screws to mount the camera is not supplied. Prepare locally procured screws matching the material, structure, and total weight of mounting place. · Be sure to use a ceiling board having enough strength to support this camera. Mounting arm (2) Remove the rear cover. (1) Remove the fixing screw. Drainage hole Junction box With the mounting screws (locally procured), fix the camera mounting arm directly to a wall or a junction box installed on the wall. 24. 5 mm {31/32"} 2. Remove the switch cover by loosening the two fixing screws. The switch unit will appear. CAUTION Mounting screws (Locally procured) x 4 Hole 6 mm (W) x 10 mm (H) {1/4" (W) x 13/32" (H)} 46 mm {1-13/16"} Cable access hole (1) Remove the fixing screw. (x 2) 83. 5 mm {3-5/16"} (2) Remove the switch cover. W V-C W 37 4 I SD I Mounting screws (Locally procured) x 4 Mounting arm 3. Connect the video input jack of LCD monitor and the monitor output jack (3. 5 mm {0. 14"} diam. Note: Refer to the illustrations for the width of plug to be inserted into the video input jack. I Connections 9mm {11/32"} or less 9mm {11/32"} or less L-type plug Straight plug I Attaching the Supplied Sun Shield Attach the sun shield to the camera head by tightening the four supplied screws. Caution: Be sure to use the four supplied screws. Video Output cable BNC plug BNC plug Brown (Live/!) Blue (Neutral/@) Green/Yellow (GND) Black (Live) For heater Gray (Neutral) (24 V AC only) Perform cable connections by referring the illustrations. Fixing screws (Supplied) x 4 (M3 x 6) Aim the arrow to this direction. Adjust the camera angle by performing 1) to 3). 1) While holding the camera head, loosen the panning lock screw. Then, move the camera head horizontally. [. . . ] Fixing screws for mounting adapter (M3 x 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 pcs. I Attaching the Switch, Rear, and Front Covers Attach the switch, rear, and front covers to the camera with the screws you have removed. Switch cover attachment Perform Step 2 of "Adjusting the Camera Angle" reversely. Rear cover attachment Perform Step 1 of "Adjusting the Camera Angle" reversely. Front cover attachment Perform Step 1 of "Adjusting the Focus" reversely. Notes: · The recommended tightening torque of switch cover fixing screws (x 2) and front cover fixing screws (x 4) is 0. 59 Nm {0. 43 lb ft. }. [. . . ]