User manual PANASONIC WV-CW484

[. . . ] Color CCTV Cameras Operating Instructions Model No. WV-CW484 Series (Lens is option. ) WV-CW484F is shown above. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual. For Canada CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This Class A digital apparatus complies with Canadian ICES-003. For U. S. A CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Setup using an optional system controller is also available. Note: The illustrations below are the examples to be displayed on a video monitor. 1. Hold down the [SET] button for around 2 seconds. Move the cursor onto "END" by press the [UP] or [DOWN] button. MODEL WV-CW484 SERIES CAMERA BACK-FOCUS SPECIAL LANGUAGE END SETUP DISABLE 3. Press the [SET] button after moving the cursor onto "SETUP" by pressing the [RIGHT] button. The "DISABLE" indication will change into "ENABLE" and the settings will become editable. MODEL WV-CW484 SERIES CAMERA BACK-FOCUS SPECIAL LANGUAGE END SETUP ENABLE 4. Move the cursor onto the desired setup item and press the [SET] button. The setup page of the selected setup item will be displayed. Select setup item: Move the cursor by pressing the [UP] or [DOWN] button. Change the parameter: Press the [LEFT] or [RIGHT] button. Display the detailed settings page of the setup item: Press the [SET] button when the setup item with the [O] mark is selected. Go back to the previous page: Move the cursor onto "RET" and press the [SET] button. Go back to the top page: Move the cursor onto "TOP" and press the [SET] button. **CAMERA SETUP** 1/2 CAMERA ID OFF ALC ALC SHUTTER OFF AGC ON(HIGH) SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF DNR HIGH RESOLUTION HIGH BW MODE **CAMERA SETUP** 2/2 PRIVACY ZONE OFF EL-ZOOM OFF UPSIDE-DOWN OFF STABILIZER OFF LENS PANASONIC RET TOP END 29 6. To exit from the SETUP menu and display images from the camera, move the cursor onto "END" and press the [SET] button. Notes: · To prevent erroneous operations, the "DISABLE" indication will always be displayed when the top page is displayed from the camera. To operate the SETUP menu, switch the "DISABLE" indication to the "ENABLE" indication first. · The cursor position will be displayed highlighted. 30 Setting Procedures First, select a language for menu display and camera ID display. Language Setup (LANGUAGE SETUP) **LANGUAGE SETUP** LANGUAGE ENGLISH 1. Select LANGUAGE on the top menu and press the [SET] button. The default setting is SET RET TOP END English. Available languages: ENGLISH, FRANÇAIS, DEUTSCH, ESPAÑOL, ITALIANO, êìëëäàâ, JAPANESE, CHINESE 3. Select SET on the menu and press the [SET] button. 1. Camera Identification Setting (CAMERA ID) Assign a name to the camera using up to 16 characters picture in the selected position. [. . . ] Is the video output cable connected to the video connector of the monitor? Confirm the cables are firmly connected. 23 · Are the brightness and contrast of monitor properly adjusted? Confirm the monitor. ­ · Aren't there dusts or dirt on the lens? Check if there are dust or dirt on the lens. [. . . ]