User manual PANASONIC WV-CW964P

[. . . ] Color CCTV Camera Operating Instructions Model No. WV-CW964 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ENGLISH VERSION For U. S. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Move the cursor to ZOOM LIMIT, and then tilt the joystick left or right to select a zoom limit setting. When doing manual operation, zoom operation cannot go beyond the zoom limit. Optical zoom ranges from 1 to 30 magnifications, while digital zoom is used for higher magnifications (up to 300). The factory default setting is x30 (30x optical zoom). Notes: · If zoom limit is set to more than 30x, then zoom operation pauses at 30x magnification. · Increasing the zoom to over 30x magnification (digital zoom) decreases the resolution. · You cannot set a zoom magnification of greater than 30x as a preset position. (13) Auto Image Stabilizer (STABILIZER) This function electronically compensates for an unstable camera image due to movement of a mounting pole or bracket. Move the cursor to STABILIZER, and then tilt the joystick left or right to turn the stabilizer on or off. The default setting is OFF ON : Automatically compensates for an unstable image. OFF : Image stabilizer will not operate. Notes: · The stabilizer may not be effective for the following subjects. Example: · Objects illuminated with low lighting · Single-color objects (white walls etc) · Fast moving periodic action, such as mechanical vibration, may not be tracked. · The stabilizer does not work during PAN/TILT/ZOOM/FOCUS or when the camera setup menu is open. · When set to ON, some effective pixels on the edge of the CCD are used by the stabilization function. This may result in a small reduction in resolution and a narrower angle of view. After activating the image stabilizer function, check that the field of view is correct. · Image stabilization may not function where there is excessive camera movement or when the scene is low light or low contrast objects. -30- PAN/TILT SETTINGS Using the Pan/Tilt Setup Menu Display the pan/tilt setup menu from the setup menu to configure pan and tilt settings. Display the setup menu (page 25), move the cursor to PAN/TILT O, and then press the CAM (SET) button. This will display the pan/tilt setup menu. **PAN/TILT PRESET 1 MAP HOME POSITION SELF RETURN AUTO MODE AUTOPAN KEY PATROL PRIVACY ZONE IMAGE HOLD DIGITAL FLIP PROPO. P/T **PAN/TILT AREA TITLE TILT ANGLE CLEANING SETUP**1/2 OFF OFF OFF AUTO PAN OFF OFF ON ON SETUP**2/2 ON(USER) 0° OFF **PRESET POSITION** 4 1* 2 3 8 5 6 7 12 9 10 11 16 13 14 15 20 17 18 19 24 21 22 23 28 25 26 27 32 29 30 31 ID:DOOR 033-064 225-256 RET TOP q e t u o !1 w r y i !0 2. Move the cursor to the number you want to select, and then press the CAM (SET) button. This registers the position number setting and displays the preset setting menu. (this page) To select a position number in the range of 033 to 064, move the cursor to 33-64 in the lower left corner of the menu, and then press the CAM (SET) button. [. . . ] If the countermeasures described below do not correct the problem, or if the symptoms you are experiencing are not covered here, contact a quality service person or system installer. Problem Cause and Recommended Action Reference Pages · Is the camera connected correctly?Check the operating instructions that come with your system controller. -- No picture (dark screen) · Is the lens iris closed?Execute the iris reset from the system controller you are using. 26-27 · Is the camera set up for a fixed shutter speed? 27 · Is the lens iris open? 26-27 White picture · Is FIX selected for the electronic sensitivity enhancement (SENS UP) setting? 27 · Is the dome cover or lens of the camera dirty?If so, clean them. 7 Out of focus picture · Is MANUAL selected for the auto focus mode? 30 · Is the object one that is not compatible with auto focus? [. . . ]