User manual PANASONIC WV-LA18

[. . . ] · The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, should be placed on the apparatus. · All work related to the installation of this product should be made by qualified service personnel or system installers. · For PERMANENTLY CONNECTED APPARATUS provided neither with an all-pole MAINS SWITCH nor an all-all pole circuit breaker, the installation shall be carried out in accordance with all applicable installation rules. · The connections should comply with local electrical code. UL listed model No: WV-LA18, WV-SF335, WV-SF332 For Canada CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This Class A digital apparatus complies with Canadian ICES-003. For U. S. A CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Additional information may be obtained from MPEG LA, LLC. See http://www. mpegla. com. 13 Precautions for Installation Installation work shall be performed in accordance with the technology standard of the electric installation. This camera is designed to be used indoors. Do not expose this camera to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this camera away from water and moisture. Installing place Do not place this product in the following places: · Locations where it may get wet from rain or water splash · Locationswhereachemicalagentisused such as a swimming pool · Locationssubjecttohumidity, dust, steam and oil smoke · Locations in a specific environment where a solvent or a flammable atmosphere exists · Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated · Locations where corrosive gas is produced, Locations where it may be damaged by briny air such as seashores · Locations where the temperature is not within ­10 °C to +50 °C {14 °F to 122 °F}. · Locationssubjecttovibrations(Thisproduct is not designed for on-vehicle use. ) · Locations subject to condensation as the result of severe changes in temperature (In case of installing the camera in such locations, the dome cover may become foggy or condensation may be caused on the cover. ) Be sure to remove this product if it is not in use. Shielded (STP) LAN cables must be used with this unit to ensure compliance with EMC standards. * * PAL models only Before installation · The camera mount bracket described on page 19 shall be used to mount the camera. · When this camera and camera mount bracket are mounted on a ceiling or a wall, use the screws described on page 19. For mounting a camera on a concrete wall, use an anchor bolt (for M4) or an AY plug bolt (M4) for securing. (Recommended tightening torque: 1. 6 N·m {1. 18 lbf·ft}) · Requiredpull-outcapacityofasinglescrew/boltis196N{44lbf}ormore. · Ifaceilingboardsuchasplasterboardistooweaktosupportthetotalweight, theareashall be sufficiently reinforced or the optional ceiling mount bracket for the camera, WV-Q105, must be used. The mounting conditions of the camera are described as follows: Installation place Ceiling/wall Ceiling/wall Ceiling Ceiling Applicable mount Recommended bracket screw Two-gang junction box (Direct mounting) WV-Q168 (approx. 280 g {0. 8 lbs}) M4 M4 ­ Number of screw 4 pcs. ­ ­ Minimum pull-out strength (per 1 pc. ) 196 N {44 lbf} 196 N {44 lbf} *2 *2 WV-Q105*1 (approx. ­ 150 g {0. 8 lbs}) *1 PAL models only *2 Make sure that the installed mount bracket can support more than 5 times of the weight of the camera. 19 Using the side cable access hole When installing the camera directly on the ceiling or wall with cables exposed or when using the optional ceiling mount bracket WV-Q168, cut out a portion of the dome cover to open a cable access hole. Side cable access hole Side cable access hole Method of camera installation Using the two-gang junction box Mount the camera on the two-gang junction box by fixing 4 screws (locally procured). ( Page 28) Direction marker for installation MO NIT OR OU T FR O TO NT P I/O EXT 2 1 43 AU OUDIO T MIC LIN Screws (locally procured) F E IN 10B 10 AS 0B A N Two-gang junction box 12 V= IN 20 Installing the camera directly on the ceiling or wall Place the installation template label (accessory) on the ceiling or wall, and make a hole to pass the cable. Remove the template label, and mount the camera by fixing 4 screws (locally procured). ( Page 28 ) Side cable access hole 83. 5 mm {3-5/16"} 46 {1- mm 13/ 40 16" mm } {19/1 6"} Direction marker for installation Recommended screw (M4: 4 pcs. ) Cable access hole for ceiling/wall MO NIT OR OU T FRO TO NT P 4 I/O 1 EXT 2 3 20 mm {13/16"} F AU D OU IO T MIC LIN E IN 10BA 100BS A Screws (locally procured) Installation template label (accessory) N 12V =IN Using the optional ceiling mount bracket WV-Q168 It is possible to reduce the exposed portion of the camera body using the optional ceiling mount bracket. Refer to WV-Q168 Operating Instructions or "Installation" ( page 28) for how to mount the camera. Using the optional ceiling mount bracket WV-Q105 (PAL models only) Refer to WV-Q105 Operating Instructions and "Installation" ( page 28) for how to mount the camera in case of using the optional ceiling mount bracket. Roof space WV-Q105 (option) Anchor bolt Safety wire angle Cable tie (accessory) Ceiling board such as plaster board (4 pcs, WV-Q105 supplied) Safety wire Camera 21 Insert/remove an SDHC/SD memory card Important: · BeforeinsertingtheSDHC/SDmemorycard, turnoffthepowerofthecamerafirst. [. . . ] 30 fps JPEG 640 × 360/320 × 180, max. Image compression method*1 *2: H. 264/MPEG-4 Image quality: Low/Normal/Fine Transmission type: Unicast/Multicast Audio bit rate: Constant bit rate: 64kbps/ 128kbps/ 256kbps/ 384kbps/ 512kbps/ 768kbps/ 1024kbps/ 1536kbps/ 2048kbps/ 3072kbps/ 4096kbps/ *8192kbps/ Unlimited * only in H. 264 mode Frame rate priority: 1fps/ 3fps/ 5fps/ 7. 5fps/ 10fps/ 12fps*/ 15fps/ 20fps/ 30fps * PAL models only JPEG Image quality: 0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/ 6/ 7/ 8/ 9 LOW (10 steps: 0-9) Transmission type: PULL/PUSH Transmission interval: 0. 1 fps - 30 fps (JPEG frame rate will be restricted when displaying both JPEG and H. 264/MPEG-4 images. ) Audio compression method: G. 726 (ADPCM) 32kbps/ 16kbps Bandwidth control: Unlimited/ 64kbps/ 128kbps/ 256kbps/ 384kbps/ 512kbps/ 768kbps/ 1024 kbps/ 2048kbps/ 4096kbps/ 8192kbps Protocol: IPv6: TCP/IP, UDP/IP, HTTP, RTP, FTP, SMTP, DNS, NTP, SNMP IPv4: TCP/IP, UDP/IP, HTTP, RTSP, RTP, RTP/RTCP, FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP Microsoft Windows 7 Professional (64-bit) OS*3 *4: Microsoft Windows 7 Professional (32-bit) Microsoft Windows Vista Business SP1 (32-bit) Microsoft Windows XP Professional SP3 Browser: Windows Internet Explorer 8. 0 (Microsoft Windows 7 Professional (32-bit/64-bit)) Windows Internet Explorer 7. 0 (Microsoft Windows Vista Business SP1 (32-bit)) Microsoft Internet Explorer 6. 0 SP3 (Microsoft Windows XP Professional SP3) Maximum concurrent access number: 14 (Depends on network conditions) FTP client: Alarm image transmission, FTP periodic transmission (When the FTP transmission is failed, backup on an optional SDHC/SDC memory card is available. ) Resolution: (WV-SF332) 41 Multi-screen: Compatible SDHC/SD memory card (option): Up to 16 camera images can be displayed simultaneously on a multi-screen. Manufactured by Panasonic SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB SD memory card: 256 MB, 512 MB, 1 GB, 2 GB (except miniSD card and microSD card) *1 Either H. 264 or MPEG-4 is selectable. *2 Transmission for 2 streams can be individually set in the same compression method. [. . . ]