User manual PANASONIC WV-LA2R8C3B

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. SA 1966 Power disconnection. [. . . ] Use a dry cloth to clean the apparatus when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently. · Do not operate the apparatus beyond its specified temperature, humidity, or power source ratings. Use the apparatus under conditions where temperatures are between 0 °C and + 40 °C {+32 °F to +104 °F}, and humidity below 90 %. The input power source for this apparatus is 100 V to 240 V AC, 50/60 Hz. * Supplied AC power cord supports 120 V AC only. To use this product with larger power source, replace the power cord. · Clear a space of more than 5 cm {2 inches} from both sides, the top, the bottom and the rear of the units. · Do not mount the monitor on places subject to constant vibrations. · Use only the supplied power cord or AC adapter. · The surface of the LCD Panel is applied by special coating. · Determines the selected parameter in setup menus. t Selection Buttons (SELECT: C, D) These buttons move the cursor in setup menus. 8 !3 Audio output connector (AUDIO OUT) Supplies an audio signal accepted by the AUDIO IN connector to another external device. · Do not install the AC adapter into the wall. That may cause temperature to rise. Places to be avoided · · · · · · Very dirty and dusty places Places subject to strong vibrations Humid places Places where drastic temperature changes occur Places which are not level Steamy and oily places such as kitchens Screw holes for VESA mounting bracket (100 mm {3-9/10"} pitch) Screws (M4, locally procured) I Removing the Monitor Stand Before mounting the monitor on the wall, remove the monitor stand. Remove the screw of stand cover (M4), and then remove the stand cover. Remove the four screws of monitor stand, and then remove the monitor stand. Mounting bracket (locally procured) Screw (4) Stand cover Monitor stand Screw (4) 10 CONNECTIONS I Connection Example PC Other video monitors PC output (VGA) Video input Audio input IN DC IN PC IN OUT IN OUT IN OUT AUDIO S-VIDEO VIDEO-B VIDEO-A Power cord (supplied) AC adapter (supplied) Audio output S-video output Video output Digital disk recorder 11 I Camera Connection Connect the video output connector of camera to the VIDEO IN connector with a coaxial cable. Note: Make sure that the cable length between the camera and monitor is as follows. Cable type RG-59/U 3C-2V RG-6/U 5C-2V RG-11/U 7C-2V RG-11/U 10C-2V Cable length 250 m {820 ft. } 500 m {1 640 ft. } 600 m {1 968 ft. } 800 m {2 625 ft. } G To Output Audio Signal Connect the AUDIO IN connector of this monitor to the audio output connector of digital disk recorder (or other recording devices) with an audio cable. I PC Connection Connect the PC IN connector of this monitor to the analog RGB output connector of PC (or another device). I Connection with Two or More Video Monitors · Connect the VIDEO OUT connector of this monitor to the video input connector of another monitor with a coaxial cable. · Connect the AUDIO OUT connector of this monitor to the audio input connector of another monitor with an audio cable. Notes: · Up to 10 monitors can be connected to this monitor. If 11 or more monitors are connected, picture quality may be degraded. [. . . ] After returning to the top menu, move the cursor to EXIT by pressing the C or D button. The monitor display return to the default status. Note: If no operation has been performed for 10 seconds or more, the monitor display returns to the default status. VIDEO ADJUST SETUP EXIT 2. Move the cursor to SETUP by pressing the C or D button. [. . . ]