User manual PANASONIC WV-LA36

[. . . ] Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framstölls i Direktiv 89/336/EEC. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivin 89/336/EEC. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som fælger bestemmelsene i direktiv 89/336/EEC. For Australia THIS APPARATUS MUST BE EARTHED. To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. [. . . ] OFF: Set this position to use with the specified Colour System Camera (Multiplexed VD(VD2) with genlock). Caution: Be sure to set this switch before camera connection. Otherwise, it may damage this monitor. OPERATING PROCEDURES POWER ON OFF STAND BY ON EXT CAMERA 4. Set the desired sequential switching interval time with the Set Up menu. 1 4 3 2 1 2 SEQUENCE 1 2 3 4 MODE INPUT SELECT V-HOLD COLOUR BRIGHT CONTRAST PICTURE MIN. AUDIO . MAX SET UP 1 Selection of Camera 2 1. Set the Power Switch (1) on the front panel to the ON position by pressing once. Press the desired Camera Selection Switch. The normal picture will not be displayed for a few seconds after turning on the power of the monitor. This monitor is in the sequence mode automatically by turning on the power of this unit. The desired camera can be observed on the monitor by pressing the desired Camera Selection Switch even if this monitor is in the sequence mode. Also desired camera picture can be observed on the monitor by pressing the desired Camera Selection Switch even if this monitor is in the Standby mode. Caution : When the power switch of monitor is turned ON and OFF repeatedly in the short period of time, the camera may not be turned ON due to the operation of misconnection protection circuit. (b) Intercom Calling The selection of the camera by intercom calling signal only is automatically reset at approx. and the selection of the camera is returned to the sequential switching. Time Lapse VTR When the Time Lapse VTR is connected with Colour Mini CCTV System, the selection of the camera by alarm sensors/intercom is automatically reset according to the reset time of Time Lapse VTR and the selection of the camera is returned to the sequential switching. -6- 1. SETUP MENU This monitor utilizes various user setup menu by using the on-screen character display. This setup menu is shown in the following. This menu is described in the following section 3 "SETUP MENU DESCRIPTION" in detail. SET UP menu SETUP DISABLE SETUP ENABLE Camera ID ON/OFF Audio Select Timing Select Sequence Time Adjust Alarm Buzzer ON/OFF Alarm Time Adjust Auto Reset Bright Compensation ON/OFF A setup operations performed by the following switches on the front panel. Up Switch (15) 3. Camera Identification (CAMERA ID) Up to 8 of alphabetic/number characters for camera identification characters can be displayed on the top line of the picture. The ID display On or Off can be set on the first line of this item and the editing of displayed characters can be made in the second line. Note: Refer to the SETUP OPERATION section for detailed procedure. Left Switch (17) SEQUENCE 1 Setup Switch (14) 2 3 4 SET UP Down Switch (16) Right Switch (18) Up Switch : Down Switch : Right Switch : Left Switch : Setup Switch : The cursor moves upwards. The adjustment of certain levels can be made by this switch. The adjustment of certain levels can be made by this switch. [. . . ] Two modes for the Alarm Control Out are selected. STD BY: This terminal is performed at only Standby mode of the Mode Selection Switch when the SPOT MONITOR CONTROL IN is activated by intercom or alarm sensor/switch. ALL MODE: This terminal is performd at either Standby or On Mode of the Mode Selection Switch when the SPOT MONITOR CONTROL IN is activated by intercom or alarm sensor/swtich. ALARM CONTROL SPOT MONITOR CONTROL IN REMOTE OUT RECOVER GND 4 3 2 1 STDBY ALL GND RESET 4 MODE 3 2 1 (+) (-) Alarm (-) (+) The polarity for the alarm and Alarm Control Output of the monitor should be matched. The power rate of the alarm should be DC24V, max. [. . . ]