User manual PANASONIC WV-LA4R5A

[. . . ] 3 Monitor Images on a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Monitor images from a single camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Monitor images from multiple cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Record images on the SD memory card manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Default: OFF [Preset No. ] [SET] button: When the position of the camera is determined using the [ZOOM] buttons, the [FOCUS] buttons, the [BRIGHTNESS] buttons and the control pad/buttons, click this button after selecting the desired preset position number (1 - 64) from the pulldown menu. The determined position will be newly registered as the preset position. Note: When "ON" is selected, the entered preset ID will be displayed at the position selected for "OSD Position" on the [Basic] tab of the "Basic setup" page. ( page 20) Important: When "Preset ID (0-9, A-Z)" or "Preset ID" is edited, it is necessary to click the [SET] button to apply them. 36 [Preset ID (0-9, A-Z)] Enter the preset ID to be displayed on images. The preset IDs can be applied to each preset position. Available characters: 0-9, A-Z and the following marks. Number of characters for the preset ID: 0 - 16 characters Default: None (blank) Note: The entered preset ID will be displayed next to the preset position number on the pull-down menu. When "ON" is selected for "Preset ID", the preset ID will be displayed on images. [Auto focus] Select "AUTO" or "OFF" to determine whether to enable or disable the auto focus function after the camera has moved to a preset position. This function can be applied to each preset position. AUTO: The auto focus function will be activated after moving to a preset position. ( page 31) When there is a zone that is not to be displayed, set the zone as a privacy zone to not to display. Notes: · Depending on the panning/tilting direction (especially when the tilting degree is 45 ° - 90 °) and the zooming factor, the area set as the privacy zone may become visible. Make sure that each of the set privacy zone is not visible after setting it. · The privacy zone function does not work when the camera is in the process of warming-up just after turning on the power, or in the process of refreshing the position. Operate the camera with the panning/tilting/zooming operations to cover the area to be covered by the blinking mask. Click the [SET] button after determining the position of the camera. To delete the registered zone, click the [DEL] button after designating the desired zone number to be deleted. Click the [CANCEL] button to cancel the application or to delete the setting. Notes: · Set the privacy zone larger than the size of an object to be hidden. To raise the precision of the privacy zone placement especially when the zoom is on the WIDE side, it is recommended to set the privacy zone with the zoom range between 1x and 3x. · Panning, tilting and zooming operations can also be carried out on the [Image/Position] tab. · When selecting "Zone No" after selecting "Gray" for "Mode", a mask will be displayed at the center of the image display area and will start blinking while changing its color as follows. [. . . ] The following are descriptions for when Microsoft XP Professional SP2 is installed on the PC in use. (1) Right-click on the desktop and select "Properties" from the displayed pop-up menu. (2) Select "Settings" from "Display Properties", and then click the [Advanced] button. (3) Click the [Troubleshoot] tab and disable the DirectDraw acceleration by adjusting the level of "Hardware acceleration". [. . . ]