User manual PANASONIC WV-LM12B2

[. . . ] Nosotros declaramos bajo nuestra única responsabilidad que el producto a que hace referencia esta declaración está conforme con las normas u otros documentos normativos siguiendo las estipulaciones de las directivas CEE/73/23 y CEE/89/336. Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive CEE/73/23 e CEE/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC. Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framställs i EECdirektiv nr. [. . . ] · All cameras connected to the network must use their own exclusive AC adapter. 17 SETUP < Settings for Connection type 2 > Item IP address Netmask Default gateway Network speed Description of the parameter Set the IP address designated by your network administrator. However, the setting is not required if the DHCP is used in an intranet. Set the subnet mask designated by your network administrator. However, the setting is not required if the DHCP is used in an intranet. Set the IP address of the default gateway designated by your network administrator. However, the setting is not required if the DHCP is used in an intranet. Use the default setting "auto" for the network speed. Selectable parameters: auto (default setting), 100 Mbps (full duplex), 100 Mbps (half duplex), 10 Mbps (full duplex), 10 Mbps (half duplex) Use the default setting "80" for the HTTP port. Refer to your network administrator and set the designated host name if required. Set to ON when using the "Panasonic IP Setup" software Set to ON if the intranet uses the DHCP. Set to ON when using the DNS. HTTP port Host name BOOTP DHCP DNS Primary server Set the IP address of the DNS server when using the DNS. · Use an Ethernet switching hub or a broadband router suitable for 10Base-T/100Base-TX. Install also a LAN card suitable for 10Base-T/100Base-TX on the PC. · All cameras connected to the network must use their own exclusive AC adapter. · To use multiple cameras, it is necessary to set up the router and assign each camera with an HTTP port number. For further information about the assignment of the HTTP port number to the camera, refer to "Parameters for the 'Network setup' Items Depending on the Connection Type" in the supplied CD-ROM. For further information about the setup of the router, refer to the operating instructions of the router. 21 SETUP < Settings for Connection type 4 > Item IP address Description of the parameter If the broadband router uses the DHCP: No setting required If the broadband router does not use the DHCP: Assignment of a private IP address is required. However, the IP addresses already assigned to the PC and other cameras are not available. For further information, refer to the operating instructions of the broadband router. If the broadband router uses the DHCP: No setting required If the broadband router does not use the DHCP: Setting of the subnet mask is required. For further information, refer to the operating instructions of the broadband router. If the broadband router uses the DHCP: No setting required If the broadband router does not use the DHCP: Assignment of an IP address to the router is required. [. . . ] Image capture size Click one of the motion picture resolution buttons (CIF (352 x 288) / QCIF (176 x 144)) to display the motion picture with the desired resolution. Adjustment of the brightness of the motion picture Click the buttons to adjust the brightness of the motion picture. The left end button (­) is the darkest and the right end button (+) is the brightest. Image Size Click one of the buttons (x1. 0 / x1. 5 / x2. 0) to select the desired motion picture size. [. . . ]