User manual PANASONIC WV-LXY23C4

[. . . ] Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The serial number of this product may be found on the bottom of the unit. [. . . ] The ALARM indicator changes from blinking to a steady light. OFF: No alarm output signal is supplied. (The alarm is deactivated. ) ALARM TERMINAL appears on the bottom of the menu when the ALARM switch is set to the lower position to connect with four sensors. ALARM SETUP ALARM DISPLAY ON SITE ALARM ON TERM. ALARM ON ALARM OUTPUT 10S ALARM BUZZER ON ALARM TERMINAL Alarm Display Setting This item lets you select whether or not to display an "ALARM" text line on the monitor when an alarm is activated. Select ON or OFF using the joystick, and then press the SET button. OFF: Display is disabled. 20 Alarm Buzzer Setting This item lets you select whether or not to sound the alarm buzzer when an alarm is activated. Select ALARM BUZZER by moving the joystick up or down. Select ALARM BUZZER ON or OFF by moving the joystick to the right or left. Note: The alarm buzzer time differs depending on (4) alarm output setting. Alarm Terminal The menu below appears when the ALARM switch on the rear of the controller is set to the lower position to receive the four sensor inputs. ALARM SETUP ALARM DISPLAY ON SITE ALARM ON TERM. ALARM ON ALARM OUTPUT 10S ALARM BUZZER ON ALARM TERMINAL Alarm Preset Position Setting This item lets you preset a camera position to an alarm input. The camera will move its pan/tilt head to the position when the alarm operates. · The menu below appears when the ALARM switch on the rear of the controller is set to the upper position to connect with a Time Lapse VCR. 1. Select ALARM TERMINAL by moving the joystick up or down. Select the most appropriate cable length by moving the joystick to the right or left. S: Less than 400 m (1 300 ft) M: 400 m (1 300 ft) to 700 m (2 300 ft) L: 700 m (2 300 ft) to 900 m (3 000 ft) (When using RG-59U, BELDEN 9259 or equivalent cable) P : Data saved. (The factory default setting for all cameras from CAM1 to CAM8 is s. ) Downloading 1. Select a camera number between CAM1 and CAM8 by moving the joystick up or down. Press the PRESET/SET/PROGRAM PRESET button. The camera number and download menu appear on the monitor as shown below. Switch Buzzer Setting This item lets you select whether or not to sound the switch buzzer when a button is pressed. Select SWITCH BUZZER by moving the joystick up or down. Select the ON or OFF mode by moving the joystick to the right or left. The initial factory setting is ON. CAM1: DOWN LOAD UP LOAD DATA TITLE 4. Select DOWN LOAD by moving the joystick up or down. Press the PRESET/SET/PROGRAM PRESET button. [. . . ] Press the PRESET/SET/PROGRAM PRESET button to execute the parameter or enter a submenu. PRESET Numeric buttons: To move the cursor. To select modes. 2 8 4 6 SET PROGRAM PRESET PRESET/SET/PROGRAM PRESET To enter a submenu. PRESET 4. Press the HOME/ESC button to return to the previous menu. HOME SET ESC PROGRAM PRESET 5. Hold down the CAMERA SETUP/SETUP/PROGRAM button for 2 seconds or more to complete the Camera Setup. CAMERA SETUP HOME/ESC button: To return to the previous menu. HOME SETUP PROGRAM ESC 32 q Camera Patrol Learning There are two ways of setting the camera patrol learning. [. . . ]