User manual PANASONIC WV-LZ628

[. . . ] 3 Viewer Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Monitor Images on a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Monitor images from a single camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Monitor images from multiple cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the HTTP port number for the camera had been changed, enter as follows: (Example: 192. 168. 0. 10:8080) Number of characters for the IP address: 1 - 128 characters Note: When using the host name, it is necessary to configure the DNS settings of the PC in use. ( page 39) [Camera title] The entered camera title will be displayed on a multiscreen. Number of characters for the camera title: 0 - 20 characters 26 Configure the alarm settings [Alarm setup] The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the alarm occurrence notification, and the VMD area settings can be configured on this page. The "Alarm setup" page has 3 tabs of the [Alarm] tab, the [VMD area] tab and the [Notification] tab. Configure the settings relating to the alarm action [Alarm] Click the [Alarm] tab on the "Alarm setup" page. ( page 15) Alarm setup The settings relating to the alarm action can be configured on this page. Refer to pages 28 and 29 for further information about the settings relating to the alarm image and the alarm out connector. [Originating port number] Select a port number to be used to receive the command alarm. Available value: 1 - 65535 Default setting: 8181 [Terminal alarm] Select "ON" or "OFF" to determine whether or not to receive the terminal alarm. Default setting: OFF [VMD alarm] Select "ON" or "OFF" to determine whether or not to perform the alarm action using the VMD function. Refer to page 30 for descriptions of how to set the VMD areas. Default setting: OFF [Command alarm] Select "ON" or "OFF" to determine whether or not to receive the command alarm. (Normally open) Default setting: Open Note: When "Open" is selected, the alarm signal will be output for around 20 seconds when the power of the camera is turned on. [Alarm output setup] Select "ON" or "OFF" to determine whether or not to output the alarm signals to the alarm out connector when an alarm is detected. Default setting: OFF [External terminal output setup] Select "Latch" or "Pulse" for the alarm out connector at an alarm occurrence. Latch: When an alarm is detected, alarm output connector will be in the state selected for "Alarm output" until the [Alarm reset] button is clicked. Pulse: When an alarm is detected, alarm output connector will be in the opposite state to the "Alarm output" setting for the period set for "Pulse width". Default setting: Latch [Pulse width] When "Pulse" is selected for "Alarm output", select an pulse width. Available value: 1 - 120 sec Default setting: 1 sec 29 Set the VMD areas [VMD area] Click the [VMD area] tab on the "Alarm setup" page. ( page 15) The video motion detection areas can be set on this page. When a motion is detected in the set area, the alarm action will be performed. Set the VMD areas Step 1 Set the video motion detection area by dragging the mouse on the screen. When the [All areas] button is clicked, the whole area will become the VMD area, and "1 (White)" will be automatically applied to "Area". The designated area will become the VMD area and the outline will be displayed. [. . . ] Then, add the IP address of the camera to "Trusted sites". · Wasn't the [Esc] key pressed before images are displayed?Close the browser window by pressing the [Alt] key and [F4] key simultaneously, etc. ­ Installation Guide Installation Guide 19 Images cannot be saved on the SD memory card. ­ ­ ­ No image is displayed on a full screen. 7 53 Symptom Cause/solution Reference pages · This may occur due to the display adapter and driver combination. When this occurred, update the driver of the display adapter to the latest version first. [. . . ]