User manual PANASONIC WV-NF284

[. . . ] Network Camera Network Operating Instructions Model No. WV-NF284 DO INS ME T ER WV-NF284 DO ME AD ER JU ST LO CK CO V CO VE R Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual. CONTENTS Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Trademarks and Registered Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The command alarm is the function that notifies of Panasonic alarm protocol from the other cameras. When "ON" is selected, alarm actions will be performed between multiple cameras. Default setting: OFF 27 Configure the settings relating to the alarm image Click the [Alarm] tab on the "Alarm setup" page. ( page 15) Alarm image setup The settings relating to the alarm image to be transmitted to the FTP server can be configured on this page. The alarm image will be transmitted to the FTP server. To transmit alarm images to the FTP server, it is necessary to configure the settings in advance. ( page 37) Refer to pages 27 and 29 for further information about the settings relating to the alarm action at an alarm occurrence and the alarm out connector. Important: Depending on the network line speed or the network traffic, images may not be transmitted at the exact designated interval or period. [File name] Enter the file name used for the alarm image to be transmitted to the FTP server. ["Entered file name" + "Time and date (year/month/day/ hour/minute/second)"] + "Serial number" Number of characters for the file name: 1 - 8 characters [Post alarm] · Transmission interval Select a transmission interval for the alarm image FTP transmission from the following. 0. 1 fps/0. 2 fps/0. 33 fps/0. 5 fps/1 fps Default setting: 1 fps · Number of images Select the number of images to be transmitted from the following. 10 pics/20 pics/ 30 pics/50 pics/100 pics/ 200 pics/300 pics/500 pics/1000 pics/2000 pics/ 3000 pics/5000 pics Default setting: 100 pics · Recording duration Approximate time to be taken to save the set "number of images" with the set "transmission interval" will be displayed. [Image capture size] Select "QVGA" or "VGA" for the image capture size of images to be transmitted to the FTP server or of an image to be attached to the alarm mail. Default setting: VGA [To FTP setup] When "To FTP setup" is clicked, the [FTP] tab of the "Server setup" page will be displayed. ( page 37) [Alarm image FTP transmission] Select "ON" or "OFF" to determine whether or not to transmit the alarm image to the FTP server. Default setting: OFF [Directory] Enter the directory name where the alarm images are to be saved. For example, enter "/ALARM" to designate the directory "ALARM" under the FTP root directory. Number of characters for the directory name: 0 - 256 characters 28 Configure the settings relating to the alarm out connector Click the [Alarm] tab on the "Alarm setup" page. ( page 15) Alarm output terminal setup The settings relating to the alarm out connector can be configured on this page. Refer to pages 27 and 28 for further information about the settings relating to the alarm action at an alarm occurrence and the alarm image. [Alarm output] Select "Open" or "Close" to determine whether to open or close the alarm output connector when output the alarm signals. Open: The alarm out connector will open when output the alarm signals. (Normally close) Close: The alarm out connector will close when output the alarm signals. [. . . ] If updating the driver does not solve the problem, adjust the hardware acceleration as follows. The following are descriptions for when Microsoft XP Professional SP2 is installed on the PC in use. (1) Right-click on the desktop and select "Properties" from the displayed pop-up menu. (2) Select "Settings" from "Display Properties", and then click the [Advanced] button. [. . . ]