User manual PANASONIC WV-NM100

[. . . ] Network Camera Operating Instructions Model No. WV-NM100 Quick Reference Guide Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht, mit der folgenden Normen oder normativen Dokumenten übereinstimmt. Gemäß den Bestimmungen der Richtlinie 73/23/EEC und 89/336/EEC. Nous déclarons sous note seule responsabilité que le produit auquel se réfère la présente déclaration est conforme aux normes ou autres documents normatifs conformément aux dispositions des directives CEE/73/23 et CEE/89/336. [. . . ] Set to ON when using the "Panasonic IP Setup" software Set to ON if the intranet uses the DHCP. Set to ON when using the DNS. HTTP port Host name BOOTP DHCP DNS Primary server Set the IP address of the DNS server when using the DNS. Secondary server Refer to your Internet service provider for the IP address of the DNS server. Primary and secondary IP addresses can be set for the DNS. 18 Using via the Internet (Connection type 3) Connecting one camera to the Internet using a cable modem. < Connection example > Cable modem Connection of a single camera To an outlet (120 V AC) AC adapter Internet Cable line < Required hardware > · Cable modem < Required cable > Ethernet cable (category 5 straight cable) !Important · Obtain the global IP address from the Internet service provider. Perform the settings of the camera by connecting the camera and the PC directly. (Refer to page 12. ) · It is required to assign the global IP address to the camera. · Use an Ethernet switching hub or a broadband router suitable for 10Base-T/100Base-TX. Install also a LAN card suitable for 10Base-T/100Base-TX on the PC. · All cameras connected to the network must use their own exclusive AC adapter. 19 SETUP < Settings for Connection type 3 > Item IP address Netmask Default gateway Network speed Description of the parameter Set the IP address designated by your Internet service provider. Set the subnet mask designated by your Internet service provider. Set the default gateway designated by your Internet service provider. Use the default setting "auto" for the network speed. Selectable parameters: auto (default setting), 100 Mbps (full duplex), 100 Mbps (half duplex), 10 Mbps (full duplex), 10 Mbps (half duplex) Use the default setting "80" for the HTTP port. Refer to your Internet service provider and set the designated host name if required. Set to ON when using the DNS. HTTP port Host name BOOTP DHCP DNS Primary server Set the IP address of the DNS server when using the DNS. Secondary server Refer to your Internet service provider for the IP address of the DNS server. Primary and secondary IP addresses can be set for the DNS. If the camera is accessed via the Internet, set the global IP address. 20 Using via the Internet (Connection type 4) Connecting one or more cameras to the Internet using an xDSL modem or a cable modem. < Connection example > Broadband router Cable modem or xDSL modem (1 port) To an outlet (120 V AC) Cable line or xDSL line AC adapter Internet To an outlet (120 V AC) AC adapter < Required hardware > · Cable modem or xDSL modem · Broadband router < Required cable > Ethernet cable (category 5 straight cable) !Important · Obtain the global IP address from the Internet service provider. [. . . ] When the picture is magnified, the quality of the picture may be decreased. AUX Click one of the buttons (High/Low) to set the status of the AUX output connector. 53 for details. ) 29 FIRMWARE UPGRADE You can upgrade the firmware of the camera to the latest version. Refer to the dealer whether the firmware upgrade is available. [. . . ]