User manual PANASONIC WV-NP1004

[. . . ] Network camera Operating Instructions Model No. WV-NP1004 PU SH TO Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. LO CK /EJ EC T WV -NP 100 4 (Lens is option. ) For Canada CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This Class A digital apparatus complies with Canadian ICES-003. For U. S. A CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] A light source such as a spot light causes a blooming (light bleeding) or a smear (vertical lines). Smear Blight subject Do not strike or shake, as this may damage the appliance. Save the configured settings We recommend that you note down your settings and save them. We assume no responsibility whatever for any damages resulting from a lost of your settings. Distributing, copying, disassembling, reverse compiling, reverse engineering, and also exporting in violation of export laws of the software provided with this product, is expressively prohibited. Blooming Router When connecting the camera to the Internet, use a broadband router with the port forwarding function (NAT, IP masquerade). Refer to the Network Operating Instructions (PDF) for further information about the port forwarding function. Radio interference When the camera is used near TV/radio antenna, strong electric field or magnetic field (near a motor or a transformer), images may be distorted and noise sound may be produced. Safety wire The safety wire holder is provided on the top of the camera. To prevent the camera from dropping that may cause accidental injury, attach one end of a safety wire (locally procured) to the safety wire holder of the camera and the other end to a locally procured safety wire holder (bracket, etc. ) to be installed on the foundation part of the building. Do not install the camera in a humid or dust-laden environment. Otherwise, lifetime of the internal parts may be shortened. 9 Major Operating Controls and Their Functions Microphone Tripod mount base Fixing screw for transportation * Remove the fixing screw before connecting the power cable. Cover for the operation buttons ALC lens connector Inside the cover for the operation buttons (Slide to the left until the cover is locked. ) Operation buttons * In these operating instructions, names of the buttons are as follows. INITIAL SET (UP) NEAR ABF/MENU FAR (LEFT) (SET) (RIGHT) (DOWN) [INITIAL SET] button [UP] button [DOWN] button [LEFT/NEAR] button [RIGHT/FAR] button [SET, ABF/MENU] button · About the [INITIAL SET] button Turn on the power of the camera while holding down this button, and wait for around 5 seconds without releasing this button. Wait another 30 seconds after releasing the button. The settings including the network settings will be initialized. However, the settings edited on the [Camera] tab of the "Camera setup" page will not be initialized. <TOP> SD memory card slot cover <BOTTOM> Screw hole for the camera mounting bracket (1/4-20UNC) Safety wire holder Screw holes for the camera mounting bracket (1/4-20UNC) <REAR> Safety wire holder AC24V IN VIDEO OUT Video out connector POWER AC 24 V terminal SD memory card error indicator (red) Link indicator 1-L 2-N Power indicator (green) SD CARD 1 2 3 4 LINK 5 GND DAY/NIGHT IN AUX OUT ALARM OUT ALARM IN GND 10BASE-T/ 100BASE-TX ACT 1 2 3 4 5 External I/O terminals Network connector Access indicator 10 Lens Mounting Mount the lens by rotating it clockwise slowly. Then, connect the lens cable to the ALC lens connector of the camera. ALC lens connector CS-mount lens (optional) Optional lens Lens type ALC lens for 1/3 inch CCD cameras 2x varifocal (high resolution) Model number WV-LZA62/2 Other lenses for 1/3 inch CCD cameras can be mounted on this camera. However, high resolution scanning of this camera may not be fully used for full-scanning (1 280 x 960) or partial scanning (960 x 720). It is recommended to use a dedicated high-resolution lens when shooting a dark subject with the aperture opened. Focus adjustment When shooting an object using an AF lens, the first adjusted focus may be out-of-focus depending on the focal depth of the lens in use. In this case, focus on a darker object with the aperture open to prevent out-of-focus. When "ABF" is selected for "BACK-FOCUS" on the SETUP menu ( page 19), the camera can automatically focus on a subject with the best available conditions even when the illumination changes. · Under near-infrared light, the focus may be slightly out-of-focus than under visible light. When the "BACK-FOCUS SETUP" page is displayed and "AUTO" or "PRESET" is selected for "C/L B/W" using the operation buttons on the camera, the camera can focus on subjects both under near-infrared light and under visible light. (However, the camera will not change the focus according to the illumination change when the focus had been adjusted once. ) Within 20 mm CS-mount: Less than 8 mm TO SH PU T EC /EJ CK LO 11 How to use a varifocal lens Before adjusting the varifocal lens, reset the flange-back length position to the default position for the CS-mount (by simultaneously pressing the [LEFT] and [RIGHT] buttons for 2 seconds or more, or by simultaneously pressing the [LEFT] and [RIGHT] buttons after pressing the [SET] button when the cursor is on "MANUAL-ADJ" on the "BACK-FOCUS SETUP" page. Method of adjustment may be different depending on the lens in use. [. . . ] · For the security enhancement, the MAC address/IP address of the camera to be configured will not be displayed when around 20 minutes have passed after turning on the power of the camera. · Panasonic IP setting software is inoperable in other subnets via the same router. Step 1 Start the Panasonic IP setting software. Step 2 Click the [IP setting] button after selecting the MAC address/IP address of the camera to be configured. Note: When using a DHCP server, it is possible to set "DNS" to "AUTO". Note: When using a DHCP server, the IP address assigned to the camera can be displayed by clicking the [Refresh] button of the IP setting software. [. . . ]