User manual PANASONIC WV-NP244

[. . . ] Network camera Operating Instructions Model No. WV-NP244 WV -NP 244 LOC K (Lens is option. ) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. CONTENTS Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Trademarks and registered trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Monitor Images on a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Level 1only/Level 2 or higher/All users Default: All users [Mic mode*] Select "ON" or "OFF" to determine whether to turn on or off audio on a PC. ON: Transmits audio from the camera to the PC. Audio can be heard with images on the PC. Images and audio will not be synchronized. OFF: Does not transmit audio from the camera to the PC. Therefore, no settings and controls relating audio will be invalidated. Default: ON [Audio bit rate] Select "16 kbps" or "32 kbps" for audio bit rate. Default: 32 kbps [Audio sensitivity] Select the sensitivity of the built-in microphone of the camera from the following. Low/Middle/High Default: Middle [Transmission interval] Select an interval for audio transmission from the followings. 20 msec/40 msec/80 msec/160 msec Default: 40 msec Note: Images and audio will not be synchronized. 26 Configure the multi-screen settings [Multi-screen setup] The cameras to be used for the multi-screen display can be registered on this page. Refer to page 16 for descriptions of how to display "Multi-screen setup" page. [IP address] Enter the IP address or the host name of the camera to be used for the multi-screen. 4 cameras can be registered as a group and up to 2 groups (8 cameras) can be registered. When the HTTP port number for the camera had been changed, enter as follows: "IP address of the camera:port number", for example "192. Number of characters for the IP address: 1 - 128 characters Note: When using the host name, it is necessary to configure the DNS settings. ( page 40) [Camera title] The entered camera title will be displayed on a multiscreen. Number of characters for the camera title: 0 - 20 characters 27 Configure the alarm settings [Alarm setup] The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the alarm occurrence notification, and the VMD area settings can be configured on this page. The "Alarm setup" page has 3 tabs of the [Alarm] tab, the [VMD area] tab and the [Notification] tab. Configure the settings relating to the alarm action [Alarm] Click the [Alarm] tab on the "Alarm setup" page. ( page 16) The settings relating to the alarm action can be configured on this page. Refer to pages 29 and 30 for further information about the settings relating to the alarm image and the alarm out connector. [Originating port number] Select a port number to be used to receive the command alarm. Available port number: 1 - 65535 Default: 8181 [Terminal alarm] Select "ON" or "OFF" to determine whether or not to receive the terminal alarm. Default: OFF [VMD alarm] Select "ON" or "OFF" to determine whether or not to perform the alarm action using the VMD function. [. . . ] Check if there are dust or dirt on the lens. · Is the focus adjusted correctly?Check if the focus is adjusted correctly. ­ Operating instructions (book) · Depending on the version of your browser, there might be difficulties refreshing the picture and operating the camera. It is recommended to use Internet Explorer 6. 0 SP2. [. . . ]