User manual PANASONIC WV-NS202A

[. . . ] Network Camera Network Operating Instructions Model No. WV-NS202A LOCK OPEN Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. CONTENTS Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Trademarks and registered trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Viewer software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When taking images under dark illumination, the camera will automatically become in the black and white mode. When taking images under bright illumination, the camera will automatically become in the color mode. Default: OFF · Approximate indication of brightness (intensity of illumination) that makes the camera to switch from the color mode to the black and white mode: Approx. 3 lx (When "ON" is selected for "AGC") · Time to be taken to switch from the color mode to the black and white mode: Approx. 5 seconds [White balance] Select a method of white balance adjustment from the following. White color can be adjusted by "Red Gain" and "Blue Gain". ATW1: Auto tracing white balance mode The camera will constantly check the color temperature of the light source and adjust the white balance automatically. Operating color temperature range is approx. ATW2: Auto tracing white balance under a sodium lamp. The camera will adjust the white balance automatically under a sodium lamp. Operating color temperature range is approx. AWC: Auto white balance control mode Suitable for shooting where the light source is fixed and the light intensity is constant. Operating color temperature range is approx. Default: ATW1 Notes: · Under the following conditions, color may not be faithfully processed. · When shooting a subject whose major part is a thick color · When shooting blue sky or sun at sunset · When shooting a subject whose luminance is too low 42 · After selecting "AWC", click the [ADJUST] button. It will take for around 7 seconds to complete the white balance adjustment. [Red Gain] Adjust the red color of images. When the cursor is moved in the "+" direction, the red color will become thicker. When the cursor is moved in the "­" direction, the red color will be thinner. Click the [RESET] button to reset the color to the default. [Blue Gain] Adjust the blue color of images. When the cursor is moved in the "+" direction, the blue color will become thicker. When the cursor is moved in the "­" direction, the blue color will be thinner. [. . . ] The "Information Bar" expressed in the following symptom and solutions will be displayed just below the address bar only when there is information to communicate. Information Bar Symptom Solutions Reference pages The following message is displayed on the information bar. To see this pop-up or additional options, click here. . . " The following message is displayed on the information bar. "This site might require the following Active X control: 'nwcv3setup. exe' from 'Matsushita Electric Industrial Co. , Ltd'. Click here to install. . . " · Click the information bar and select "Always Allow Pop-ups from This Site. . . ". [. . . ]