User manual PANASONIC WV-NS324

[. . . ] Color CCTV Camera Operating Instructions Model No. WV-NS324 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ENGLISH VERSION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. For U. S. A SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Warning: This equipment generates and uses radio frequency energy and if not installed and used properly, i. e. , in strict accordance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. The serial number of this product may be found on the top of the unit. [. . . ] Panning speed The panning speed increases when the joystick is moved to the right, and decreases when it is moved to the left. ** AUTO PAN ** POSITION SPEED PAN LIMIT ENDLESS DWELL TIME RET START END ····|···· L H OFF OFF 2S PAN LIMIT ENDLESS DWELL TIME RET OFF: The camera pans from the starting point to the endpoint, and rotates backward to the starting point. This movement is repeated over and over. Dwell time The factory default setting is 2S. Dwell time changes as follows: -35- 2S 30S 3S 20S 5S 10S Cleaning (CLEANING) CLEANING is used for refreshing the electro-mechanical contacts built into the camera. Use this function for maintenance when the camera has been directed at a specific spot or panned over a specific range for a long time. Built-in electric mechanical contacts are refreshed at regular intervals (approx. A dry contact adversely affects picture quality and motor operation. ** AUTO PAN ** POSITION SPEED PAN LIMIT ENDLESS DWELL TIME RET START END ····|···· L H OFF OFF 2S Notes: · When the panning or tilting in the AUTO PAN mode is controlled manually, the Auto mode function should be cancelled. To activate the auto mode, select the AUTO PAN mode again or set a time for SELF RETURN in the SET UP menu. · Auto refreshing may be activated during the auto mode to calibrate the lens position. ** SET UP MENU ** PRESET 1 O MAP O HOME POSITION OFF SELF RETURN OFF AUTO MODE OFF FLIP-A-CHIP OFF CLEANING ON IMAGE HOLD OFF CAMERA O NETWORK O The factory default setting is OFF. ON: The contacts are cleaned for approx. "CLEANING" disappears when the process is completed. Flip-A-Chip Setting FLIP-A-CHIP is for setting the movement of the camera by using the joystick. The factory default setting is OFF. ** SET UP MENU ** PRESET 1 O MAP O HOME POSITION OFF SELF RETURN OFF AUTO MODE OFF FLIP-A-CHIP OFF CLEANING OFF IMAGE HOLD OFF CAMERA O NETWORK O CLEANING OFF: No contact cleaning Note: Select OFF when the camera downloads or uploads preset data. OFF: Tilt range is limited to 0 ° to 92 °. ON: The flip-a-chip function allows the tilt angle to widen up to 180 °. Image Hold (IMAGE HOLD) Note: Flip-a-chip does not work if PAN LIMIT is set to ON. The camera picture remains as a still image on the monitor screen until the camera reaches the preset position. The factory default setting is OFF. ** SET UP MENU ** PRESET 1 O MAP O HOME POSITION OFF SELF RETURN OFF AUTO MODE OFF FLIP-A-CHIP OFF CLEANING OFF IMAGE HOLD ON CAMERA O NETWORK O -36- Camera Setting To Display the Camera Setting Menu Move the cursor to CAMERA O, and press the CAM (SET) key. The camera setting menu appears. ** SET UP MENU ** PRESET 1 O MAP O HOME POSITION OFF SELF RETURN OFF AUTO MODE OFF FLIP-A-CHIP ON CLEANING OFF IMAGE HOLD OFF CAMERA O NETWORK O To Enter a New Camera ID (1) Move the cursor to the desired character using the joystick, and press the CAM (SET) key. (2) The selected character appears in the editing area. (The pointer in the editing area moves to the right automatically at this moment. ) To enter a blank, select SPACE. (3) Repeat the above procedure until all characters are entered. Note: Refer to page 32 for POSI, RET and RESET. CAMERA ID -0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ (). , '":;&#!?= +-*/%$ SPACE ---- POSI RET RESET . . . . . . . . . . . . . . . . ** SET UP ** CAMERA ID ON O ALC/MANUAL ALC O SHUTTER OFF AGC ON(MID) SYNC INT WHITE BAL ATW O AF MODE MANUAL EL-ZOOM ON SENS UP OFF MOTION DET OFF RET SPECIAL O Light Control Setting (ALC/MANUAL) You can select the mode for adjusting the lens iris. There are two modes as follows: ALC: The lens iris is automatically adjusted to suit the brightness of the object. You can select one of two modes (BLC ON or BLC OFF) of backlight compensation. [. . . ] 3. 0 s (FAR/NEAR) in manual mode 360 ° endless possible (in auto-pan mode) manual/auto pan manual : approx. 1. 0 °/s to 100 °/s, 8-steps/64-steps preset position : maximum approx. 100 °/s 0 ° to 92 ° manual manual : approx. 1. 0 °/s to 100 °/s, 8-steps/64-steps preset position : maximum approx. [. . . ]