User manual PANASONIC WV-NW484S

[. . . ] Network Camera Operating Instructions Model No. WV-NW484S Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. WARNING: · This apparatus must be earthed. · All work related to the installation of this product should be made by qualified service personnel or system installers. · The connections should comply with local electrical code. For Canada This Class A digital apparatus complies with Canadian ICES-003. For U. S. A NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Choose screws in accordance with the materials and structure of the installation location. · Screws for fixing the camera to the bracket are provided with the camera. 20 Installing the Camera 1 Install the mounting bracket. Fix the mounting bracket directly into the ceiling or wall or into the imbedded box using the four screws prepared in advance. (Note that screws for installation are not provided. ) When using the imbedded box, we recommend using two boxes in a row as shown in the figure below on the right. (This is to make it easier to pass the cables through. ) 85 mm Cable pass-through hole 85 mm Cable pass-through hole 51 mm Center of metal installation bracket Installation screws x 4 46 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note · When installing the camera outdoors, waterproof the screws and screw holes. 83. 5 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation screws x 4 2 Loosen the three screws and remove the enclosure. Unscrew the screws using the driver bit (provided). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note · When replacing the dome cover (WV-CW4C, sold separately), refer to the Operating Instructions provided with the dome cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Installing the Camera (continued) 3 Unscrew the transportation screw. Transportation screw 4 Connect the power cable and the video output cable. See "Waterproofing Cable Joints" on page 26. Imbedded box for camera installation Imbedded box for connecting cables 22 5 Install the camera on the mounting bracket. Fix the camera onto the mounting bracket using the four screws (provided). During installation, align the protruding part on the mounting bracket and the indented part on the camera to fix the position of the camera. Make sure to tighten the screws used for mounting the camera. (M4:0. 78 N·m) {8kgf·cm} You can keep the camera waterproof by firmly tightening the installation screws. Mounting bracket Camera body 2 positioning convex parts (left and right) 2 positioning concave parts (left and right) Installation screws Installation screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note · When using the embedded box, run the cable as shown on the right. Cable Imbedded box Camera Mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Installing the Camera (continued) 6 Adjust the camera angle while monitoring the image on the adjustment monitor. See "Adjusting the Camera" on page 28. Tighten the screws unscrewed at step 3 using the driver bit (provided). Align the mark on the side of the enclosure with the line on the side of the bracket. (recommended torque: 0. 78 N·m {8 kgf·cm}) 75° Monitor output connector (mini-jack) Tilt adjustment seat 7 Panning table Tilt lock screw Pan lock screw Line on the side A Marking on the side Installation bracket Enclosure Enlarged view of A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note · When installing the enclosure, the camera focus may shift slightly out of position. So, either hold the ABF button down for at least two seconds before installing the dome cover, or make the final adjustment on the PC after installing the dome cover. ( page 28) · When installing an SD memory card, insert the card before installing the enclosure. ( page 32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Connecting the Cables Network cable RJ-45 female/female conversion connector (included) Alarm I/O cable 4P alarm cable (included) Power cord (24 V AC/12 V DC) Brown (Live) Blue (Neutral) Green/Yellow (GND) Power cable 24 V AC Brown (Live) Blue (Neutral) Green/yellow (GND) Live Neutral Connect to ground. [. . . ] : Alarm action will be performed when a Panasonic alarm notice is received from a connected device via the network. Scene change detection alarm Command alarm Action at an alarm occurrence · Display of the [Alarm occurrence indication] button on the "Live" page ( Setup Manual) The [Alarm occurrence indication] button will be displayed and will blink on the "Live" page when an alarm occurs. 43 Action at an alarm occurrence (continued) Important · When "Polling(30 sec)" is selected for "Alarm status update mode", the alarm occurrence indication button will be refreshed in 30-second intervals. For this reason, it may take a maximum of 30 seconds until the alarm occurrence indication button is displayed on the "Live" page when an alarm occurs. ( Setup Manual) 44 Viewing Help If you want to know anything about operation or setup methods on screen, display the "Help" screen. Displaying the Help screen · Setup screen 1 1 2 Click the [Setup] button. The "Help" screen is displayed. 2 · Help screen Click the desired item to display a detailed explanation for the corresponding operation. 45 Troubleshooting Before requesting service, check the following items. [. . . ]