User manual PANASONIC WV-Q70

[. . . ] Position two of the spring hooks of the camera as shown in the illustration below. When the ceiling mount bracket is installed after positioning them in the opposite side, they may become hard to pull out. NM1206-1027 3TR004924BAA Printed in Japan Main body Move the hook head downward. Spring hook Features This ceiling embedded bracket is exclusively designed to mount the Network Camera, WV-NF284, on a ceiling. This bracket is an embedded type to reduce the exposed portion of the camera body. This ceiling mount bracket is the embedding type so that the camera body will be dwarfed. [. . . ] This ceiling mount bracket is the embedding type so that the camera body will be dwarfed. Fix the ceiling mount bracket onto the ceiling board. Loosen the clamping screws until the length between the clamp plates becomes wider that the thickness of the ceiling board, and then clamp the ceiling board by tightening the clamping screws. Triangle mark Main body * The "Panasonic" logo on the camera should be located on the side of this triangle mark. Precautions · Refer installation work to the dealer. Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Failure to observe this may cause a fall of an inappropriate camera resulting in injury or accidents. · Mount WV-NF284 on this bracket exclusively. · Select an installation area that can support the total weight. If a selected area is too weak to support the total weight, a fall of the product may occur resulting in injury. · Installation work shall be started after sufficient reinforcement. After tightening the screws, perform visual check to ensure tightening is enough and there is no backlash. Maximum thickness of the ceiling board is 30 mm {1. 18"} for installation. Clamp plates * Clamping screw * Tightening torque: 0. 61 N·m {6. 0 kgf·cm} Clamp the ceiling board. Important: · When the ceiling board is the plasterboard, make sure that no crack was made on the ceiling board by clamping. 4. Fix the camera mount bracket provided with the camera using the provided four fixing screws. Attach the safety wire to the safety wire holder of the camera. Fix the camera on the camera mount bracket using the camera fixing screw provided with the camera. Make adjustments and attach the dome cover to the camera. (Refer to the operating instructions of the camera. ) q Adjust the angular field of view and the focus. e Fix the dome cover using the dome cover fixing screw. Main body Camera mount bracket (Camera accessory) Fixing screw (standard accessory) Tightening torque: 1. 6 N·m {16 kgf·cm} Safety wire Safety wire holder Camera fixing screw (Camera accessory) Main body of the camera (To be continued reverse page) Installations (continued) 6. Pull out both the spring hooks and attach the hooks to the cover. Make sure that the cover is attached to the ceiling with no space between them. Specifications Ambient temperature: Dimensions: Weight: ­10 °C to +50 °C {14°F - 122°F} ø186 mm {7. 31"} embedding depth of 65 mm {6. 56"} Approx. [. . . ] e Fix the dome cover using the dome cover fixing screw. Main body Camera mount bracket (Camera accessory) Fixing screw (standard accessory) Tightening torque: 1. 6 N·m {16 kgf·cm} Safety wire Safety wire holder Camera fixing screw (Camera accessory) Main body of the camera (To be continued reverse page) Installations (continued) 6. Pull out both the spring hooks and attach the hooks to the cover. Make sure that the cover is attached to the ceiling with no space between them. Specifications Ambient temperature: Dimensions: Weight: ­10 °C to +50 °C {14°F - 122°F} ø186 mm {7. 31"} embedding depth of 65 mm {6. 56"} Approx. 285 g {0. 62 lbs. } Camera Standard Accessories Operating instructions (this document). . . . . . . . . . . . . . . . [. . . ]