User manual PANASONIC WV-RC100

[. . . ] Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framstölls i Direktiv 73/23/EEC och 89/336/EEC. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ia 89/336/EEC. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som fælger bestemmelsene i direktiven 73/23/EEC og 89/336/EEC. For Australia THIS APPARATUS MUST BE EARTHED. To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. [. . . ] When an intercom or alarm sensor is connected to the spot monitor control terminal, the alarm output signal is supplied from the STD BY or ALL MODE terminal to the time lapse VTR or buzzer. STD BY-GND Connection The alarm output signal is supplied only when the DISPLAY MODE switch is set to STD BY. ALL MODE-GND Connection The alarm output signal is supplied regardless of the display mode. REMOTE OUT These terminals supply the remote control output signal or recover output signal when the camera is selected manually or automatically, or by using external control. Timing Select Output Connector (TIMING SELECT, OUT) This connector supplies the timing pulse signals for switching in the sequence operation of other extensible systems, such as another CCVE system or sequential switcher. This connector sends the signal that is supplied to the TIMING SELECT IN connector. Timing Select Input Connector (TIMING SELECT, IN) This connector receives the external timing pulse for the sequential operation from the time lapse VTR or another CCVE system. The SET UP MENU is not displayed unless a camera is connected. (Refer to "CONNECTIONS" on page 11. ) The SET UP MENU is described in detail in the following section "Setting Procedure". Set the DISPLAY MODE switch to ON to display the SET UP MENU. Set the INPUT SELECT switch to CAMERA to display the SET UP MENU. If set to VTR, the SET UP MENU is not displayed. In the upper line, you can set whether to have the camera ID displayed or not. ON: The camera number (1, 2, 3 or 4) indicates that the picture is displayed with the camera ID. OFF: The "·" mark indicates that the picture is displayed without the camera ID. The lower line is used to edit the camera ID. 1-1. Move the cursor to CAMERA ID and select the desired camera by using the Left (A) or Right (B) switch. To display the camera identification, press the SET UP switch repeatedly. After completing step 1-1, move the cursor to the second line by using the Down (C) switch. Press the SET UP switch and set the camera identification as in 1-3 below. Select the camera identification from the characters shown below. (D) (C) 0123456789:;ABCDEFGHIJKLMN OPQRSTUVWXYZÄÜÖÆÑÅØ"#'() + , - . (space) ** SET UP MENU ** CAMERA ID 1 AUDIO SELECT TIMING SELECT SEQ TIME ADJ ALARM BUZZER ALARM TIME ADJ AUTO RESET MANUAL SKIP END SET UP 1234 CAMERA SEQ INT 1 SEC ON 60 SEC ON 1234 ENABLE Use the Up/Down switches (D/C) to select characters. To correct the character that is edited wrongly, press the Left/Right switches (A/B) to select the character to be corrected and press the Up/Down switches (D/C) to select a new character. [. . . ] · Connect the Sync Timing Cable between the monitors. TIMING SELECT: INT Video Monitor WV-RC100 SPOT MONITOR CONTROL IN RECOVER GND 4 3 2 ALARM CONTROL REMOTE OUT OUT ALL 1 STDBY MODE GND RESET 4 3 2 1 TIMING SELECT OUT IN Video Monitor WV-RC100 CAMERA CAMERA EXTENSION IN AUDIO AUDIO OUT IN REC OUT PLAY IN 4 CAMERA INPUT 3 2 1 VTR CAMERA CAMERA EXTENSION IN AUDIO AUDIO OUT IN REC OUT PLAY IN 4 CAMERA INPUT 3 2 1 VTR Coaxial Cable Coaxial Cable TIMING SELECT: EXT Camera Extension Unit WV-AD110A SPOT MONITOR CONTROL IN RECOVER GND 4 3 2 ALARM CONTROL REMOTE OUT OUT ALL 1 STDBY MODE GND RESET 4 3 2 1 TIMING SELECT OUT IN Video Monitor WV-RC100 CAMERA CAMERA EXTENSION IN AUDIO AUDIO OUT IN REC OUT PLAY IN 4 CAMERA INPUT 3 2 1 VTR Camera Extension Unit WV-AD110A Coaxial Cable Coaxial Cable Additional Cameras Notes: · Set TIMING SELECT in the SET UP MENU to INT for the master monitor and to EXT for the slave monitor. · When no cameras are connected, the monitor picture is unstable. This is normal and not a malfunction. -12- s Connection with the VTR Video Monitor WV-RC100 Note: Avoid the following connection if you want to monitor the playback picture of a VTR. Video Monitor WV-RC100 CAMERA CAMERA EXTENSION IN AUDIO AUDIO OUT IN REC OUT PLAY IN 4 CAMERA INPUT 3 2 1 VTR PLAY IN VIDEO OUTPUT Time Lapse VTR TL BNC Connector Coaxial Cable VIDEO OUTPUT TL REC OUT Other Monitor VIDEO INPUT Time Lapse VTR Noise Connect a coaxial cable between the video output connector of the VTR and the PLAY IN of this monitor. s Connection with the Intercom and Alarm Sensors · Use two-wire connections for the intercom system and alarm sensors/switches. · The power source for the intercom system and alarm sensors/switches should be less than DC 12V. [. . . ]