User manual PANASONIC WV-RC37

[. . . ] Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framstölls i Direktiv 89/336/EEC. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivin 89/336/EEC. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som fælger bestemmelsene i direktiv 89/336/EEC. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lighthing flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Display the Tilt/Pan Menu as shown in Fig. 11 by repeating the previous procedures. 4. Receiver Control Press the Program (PROG) Switch for more than 2 seconds to display the Program Menu. Move the cursor to the "Receiver Control" position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to display the following display on the monitor screen. ** Program Menu ** Tilt / Pan Camera Control * Receiver Control * Camera Set Up * Controller Set Up * B Tilt / Pan Fig. Press the Up (D) Switch or the Down (C) Switch to move the Pan/Tilt Head toward up or down. Press the Right (B) Switch or the Left (A) Switch to move the Pan/Tilt Head toward right or left. While pressing these switches, the character is inversely displayed on the monitor screen. If the Up (D) Switch and the Right (B) Switch are pressed at the same time, the Pan/ Tilt Head moves diagonally towards Up and Right. 2. Press the Up (D) Switch or the Down (C) Switch to adjust the lens zoom to achieve the desired picture while observing the monitor screen. Press the Up (D) Switch to optically bring an object closer, pressing the Down (C) Switch has the reverse effect. Press the Right (B) Switch or the Left (A) Switch to adjust the lens focus to achieve a sharply picture while observing the monitor screen. 4-2. Move the cursor to the "Disable" position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch and "Enable" is displayed. ** Controller Set Up ** System * Communication * ** Controller Set Up ** System * B Communication * Set up Disable Set up Enable Fig. Select the desired item by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to select item where the cursor is positioned. Press the Program (PROG) Switch to return to the previous Program Menu as shown in Fig. To return to the normal camera picture, press the Program (PROG) Switch again. B Communication * Fig. 17 Note: When Mode Selection Switch is selected at System (SYSTEM) position, Controller Set Up Menu appears by pressing the Program (PROG) Switch for more than 2 seconds. -22- 6-2. Display the Controller Set Up Menu by repeating the previous procedures. ** Controller Set Up ** System * Communication * ** System ** Camera ID Off * Cable Comp S Alarm Time 60 S Alarm Display Off 5. Press the Program (PROG) Switch to return to the previous Program Menu. To return to the normal camera picture, press the Program (PROG) Switch again. Display the System Menu as shown in Fig. 20 by repeating the previous procedures. ** System ** Camera ID Off * Cable Comp S Alarm Time 60 S Alarm Display Off B Set up Enable Return Fig. Move the cursor to the "System" position by pressing the Up (D) Switch or the Down (C) Switch, then press the Set Switch to display the System Menu as shown in Fig. [. . . ] Select the alarm data transmission mode as follows. Off: The controller does not transmit alarm data to the computer. Auto 1: The controller relays alarm data every time it receives data from the camera. Auto 2: The controller transmits alarm data periodically to give the computer time to process the latest data before receiving new data. [. . . ]