User manual PANASONIC WV-SF332E

[. . . ] Installation Guide Network Camera Model No. WV-SF336, WV-SF335 WV-SF332 WV-SF336E, WV-SF335E WV-SF332E WV-SF336 (This illustration represents WV-SF336. ) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. WARNING: · Apparatus shall be connected to a mains socket outlet with a protective earthing connection. · The mains plug or an appliance coupler shall remain readily operable. · To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture. [. . . ] · When this camera and camera mount bracket are mounted on a ceiling or a wall, use the screws described on page 19. Prepare the screws according to the material, structure, strength and other factors of the mounting area and the total weight of objects to be mounted. · Ensure that the mounting surface, anchor and screws are sufficiently strong. · Do not mount this product on a plaster board or a wooden section because they are too weak. If this product is unavoidably mounted on such a section, the section shall be sufficiently reinforced or use an optional ceiling mount bracket (WV-Q105). Screw tightening · The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. Use of an impact driver may damage the screws or cause tightening excessively. · When a screw is tightened, make the screw at a right angle to the surface. After tightening the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash. 14 Radio disturbance When this product is used near TV/radio antenna, strong electric field or magnetic field (near a motor, a transformer or a power line), images may be distorted and noise sound may be produced. PoE (Power over Ethernet) Use a PoE hub/device that is compliant with IEEE802. 3af standard. Router When connecting this product to the Internet, use a broadband router with the port forwarding function (NAT, IP masquerade). Refer to the Operating Instructions (PDF) for further information about the port forwarding function. Time & date setting It is necessary to set the time & date before putting this product into operation. Refer to the Operating Instructions (PDF) for further information about the time & date setting. 15 Major operating controls Dome cover Inner dome Clear dome (Provided only for service) Monitor out connector for service* Direction marker for installation Azimuth adjustment ring Marker Monitor out connector for adjustment (RCA jack) FRONT TOP EXT MONITOR OUT View from the side BASE-T/ BASE TX TOP LOCK Tilting table 12V IN Panning lock screw [LOCK] Panning table 12 V DC power supply terminal * This connector is provided only for service. Do not use the connector for checking the adjustment of the angular field of view on the video monitor. 16 <Side view> SDHC/SD memory card slot Access indicator (blinking at accessing) Link indicator (lighting at linking) INITIAL SET button Focus assist (F. A. ) button SF335 SF332 FOCUS ASSIST Auto focus (AF) button SF336 AF Tilting lock screw SDHC/SD memory card error indicator/F. A. indicator (Lights when the focus assist function is activated or when the focus ring is positioned near the best focus position) SF335 SF332 SDHC/SD memory card error indicator/AF indicator (Blinks when AF is being adjusted) SF336 External I/O terminals NT FRO TOP EX 4 3 T I/O 2 1 Audio output connector Microphone/line input connector AUDIO OUT MIC/ IN LINE SE-T/ 10BA ASE-IX 100B MON ITORT OU Lens SF336 Network connector Zoom lock knob N F F Focus lock knob SF335 About the [INITIAL SET] button After turning off the power of the camera, turn on the power of the camera while holding down this button, and wait for around 5 seconds or more without releasing this button. Wait around 2 minutes after releasing the button. The camera will start up and the settings including the network settings will be initialized. Before initializing the settings, it is recommended to write down the settings in advance. N 17 Detaching the dome cover Important: · Afterremoval, retainthedomecoverfixingscrewsoasnottolose. Thescrewisrequiredwhen attaching the dome cover. ( Page 34) · Removethecoverfilmfromthedome section of the dome cover after the installation is complete. Do not touch the dome section by hand directly after removing the cover film. z Remove the dome cover fixing screw (M3, step screw, x1). LOCK OPEN ADJUST Dome cover fixing screw (M3, step screw) x Rotate the dome cover counterclockwise two steps, and align the indication "OPEN" to the maker of the camera to detach the dome cover. Marker OPEN LOCK ADJUST Dome alignment indication "OPEN" LOCK ADJUST OPEN Dome cover Dome section 18 Preparations When installing the camera on a wall or a ceiling, there are four methods as specified below. · Usingthetwo-gangjunctionbox · Installingthecameradirectlyontheceilingorwall · UsingtheoptionalceilingmountbracketWV-Q168(forembeddedinstallationonaceiling) · UsingtheoptionalceilingmountbracketWV-Q105*1 (for direct mounting on a ceiling) Important: · Procure4screws(M4)tosecurethecameratoawalloraceilingaccordingtothematerialof the installation area. [. . . ] *3 Refer to "Notes on Windows Vista / Windows 7" (PDF) for further information about system requirements for a PC and precautions when using Microsoft Windows 7 or Microsoft Windows Vista. *4 When using IPv6 for communication, use Microsoft Windows 7 or Microsoft Windows Vista. Standard accessories Installation Guide (this document) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty card (NTSC model only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CD-ROM*1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]