User manual PANASONIC WV-VF39

[. . . ] Ask a qualified service person for servicing. The camera could be damaged by improper handling or storage. Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately and ask a qualified service person for servicing. [. . . ] Do not use strong or abrasive detergents when cleaning the camera body. Use a dry cloth to clean the camera when dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently. Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol. Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused. Do not operate the camera beyond the specified temperature, humidity or power source ratings. Use the camera under conditions where temperature is between ­10°C - +50°C (14°F 122°F), and humidity is below 90 %. MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS i !0 r ty VIDEO OUT e w VOLUME MIN q POWER MAX u o ALC SOFT OFF OFF ELC SHARP BLC ON MIC ON !5 !6 ALC SOFT OFF OFF ELC SHARP BLC ON MIC ON !1 !2 !3 !4 q Camera Mounting Bracket Install on the wall or ceiling. w Pan Fixing Ring Tighten after adjusting the pan angle. If the power of these units are ON during connections, the camera does not function due to protect circuit from misconnection. · Basic System Connect the single coaxial cables between the Camera and Camera Input Terminal of Specified monitor or Camera Drive Unit. maximum cable length is as: Mounting the Lens Caution: Before you mount the lens, loosen the two screws on the ring, and rotate this ring clockwise until it stops. If the ring is not at the end, the inner glass or CCD image sensor may be damaged. q Mount the lens by turning it clockwise on the lens mount of the camera. w Connect the lens cable to the auto iris lens connector on the side of the camera. Coaxial Cable Type RG-59/U RG-6/U Maximum Cable Length 200 m (660 ft) DC R/1 000 ft. of Inner Conductor Screws Less than 30 500 m (1 650 ft) Less than 12 q w The maximum DC resistance between the camera and these units is 20 . · Connection Diagram Video Monitor WV-CM143 SPOT MONITOR CONTROL IN ALARM CONTROL REMOTE OUT TIMING SELECT OUT IN FOCUS CAMERA EXTENSION IN RECOVER GND 4 3 2 1 STDBY ALL GND RESET 4 MODE 4 CAMERA INPUT 3 2 3 2 1 AUDIO OUT AUDIO IN VIDEO OUT VIDEO IN 1 CAMERA POWER ON OFF Flange-back Adjusting Ring Coaxial Cable Caution for Mounting the Lens The lens mount should be a C-mount or CS-mount (1"-32UN) and the lens weight should be less than 450 g (0. 99 lbs). If the lens is heavier, both the lens and camera should be secured by using the supporter. The protrusion at the rear of the lens should be as shown in the diagram. Colour Video Monitor Camera Video Audio CAMERA IN VIDEO OUT AUDIO OUT VD/SYNC IN VD/SYNC OUT CS-mount: Less than 8 mm (5/16") Caution: To use the C-mount lens, the Lens Mount Converter (C-mount adapter) WVAD20 should be used with the camera. CAUTION USE WITH SPECIFIED EQUIPMENT SEE ITS MANUAL BEFORE CONECTING. SIGNAL GND Camera Drive Unit WV-PS11B FOCUS OR FLANGE-BACK ADJUSTMENT The following adjustment should be made by qualified service personnel or system installers. q Loosen the screws on the flange-back adjusting ring. w Turn the flange-back adjusting ring to the desired position. [. . . ] w Turn the flange-back adjusting ring to the desired position. Caution: Do not rotate the ring counterclockwise by force after it stops. If the ring is rotated by force, the inner lens or CCD image sensor may be damaged. e Tighten the screws on the flange-back adjusting ring. Flange-back Adjusting Ring w qe Screws INSTALLING PROCEDURE The mounting bracket can be fixed either on the top or the bottom cover of the camera. [. . . ]