User manual PANASONIC WV-VF42

[. . . ] 480 lines of horizontal resolution (Color normal mode) 510 lines of horizontal resolution (Color High Resolution mode) 570 lines of horizontal resolution (Black-and-white mode) 5. High quality picture: (a) 2H type vertical enhancer for greater picture sharpness (b) Chroma averaging circuit for better color signal-to-noise ratio (c) Minimum of aliasing on fine objects (d) Expanded dynamic range by use of knee circuit (e) Highlight aperture correction for greater picture detail of bright objects 6. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF 7. Auto black-and-white mode enables the camera to switch between color and black-and-white picture in response to Light input. [. . . ] w Pan lock screw Fixes the panning position. e Tilting lock screw Fixes the tilting position. Move the cursor to MASK SET and press I(S). The 48 mask areas appear on the monitor screen. The cursor is blinking in the upper left corner of the screen. LEVEL RET END . . . I. . . . . + Blinking Notes: · When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this item. · When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has priority so that the SUPER-D2 function is not activated automatically. · While the SENS UP function is selected, noise, spots or a whitish phenomenon may appear in the picture when the sensitivity of the camera is increased. This is a normal phenomenon. RET END Manual Fine Adjustment for AWC/ATW You can set the white balance items manually. Press I(L) or I(R) to obtain the optimum amount of red gain. Press I(L) or I(R) to obtain the optimum amount of blue gain. 9-7. Consequently, the blemish compensation position is set up and the PIX OFF menu is restored. After a blemish compensation position is set up, "*" is attached at the right of the number. If you would like to delete a blemish compensation position, move the cursor to the applicable number and press I(S). Gain Control: White Balance: Aperture: Super Dynamic2: Electronic Shutter Speed: Lens Focal length: Maximum aperture ratio: Angular field of view: Focusing range: Ambient Operating Temperature: Ambient Operating Humidity: Power Source and Power Consumption: Dimensions: 768 (H) x 494 (V) pixels, Interline Transfer CCD 4. 8 (H) x 3. 6 (V) mm (Equivalent to scanning area of 1/3" pickup tube) 525 lines/60 fields/30 frames 15. 734 kHz 59. 94 Hz Internal, Line-locked or Multiplexed vertical drive (VD2) Sync selectable 1. 0 V[P-P] NTSC composite 75 /BNC connector 480 lines (C/L Normal), 510 line (C/L, HIGH), 570 lines (B/W) 50 dB (Equivalent to AGC Off, weight On, AP On) 46 dB (Typ) 2. 0 lx (0. 20 footcandle) (WIDE) (C/L), 0. 2 lx (0. 02 footcandle) (WIDE) (B/W) When the optional WV-CW2C dome cover is installed. 0. 8 lx (0. 08 footcandle) (WIDE) (C/L), 0. 1 lx (0. 01 footcandle) (WIDE) (B/W) ON (HIGH, MID, LOW)/OFF selectable ATW1, ATW2 or AWC (SET UP MENU) selectable Set Variable (SET UP MENU) ON or OFF (SET UP MENU) selectable OFF, 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, 1/10 000 s selectable 3. 8 mm - 8 mm 1:1. 4 (Wide), 1:1. 8 (Tele) Horizontal: 35. 6 ° - 73. 6 ° Vertical: 26. 6 ° - 53. 4 ° 1. 2 m - (3. 9 ft - ) ­10 °C - +50 °C (14 °F - 122 °F) Less than 90 % 24 V AC 60 Hz, 3. 4 W, 12 V DC 335 mA WV-VF42: 133 mm (H) x 152. 5 mm (D) 5-1/4" (H) x 6" (D) WV-CW474AS: 136. 5 mm (H) x 160 mm (D) 5-3/8" (H) x 6-5/16" (D) WV-VF42: 1. 2 kg (2. 7 lbs. ) WV-CW474AS: 1. 7 kg (3. 8 lbs. ) + 4. To cancel masking, move the cursor to that area and press I(S). After masking is completed, press I(S) for 2 seconds or more. If you want to change the video output level (picture contrast), move the "I" cursor for LEVEL and adjust the level. Note: If ON is selected for SUPER-D2, a shadow (black line) may appear at the boundary between the bright and the dim scene. This is a natural phenomenon and does not indicate trouble. 6-1. Line-lock Sync Mode (LL) Turns to white Blinking 3. Shutter Speed Setting (SHUTTER) Note: To select electronic shutter speed, select OFF for SUPER-D2 in the ALC CONT menu. [. . . ] Note: ATW1 and ATW2 do not appear for WHITE BAL on the system controller setup menu. · Automatic White Balance Control Mode (AWC) In this mode, accurate white balance is obtained within a color temperature range of approximately 2 300-10 000K. Move the cursor to WHITE BAL and select AWC PUSH SW. Press I(S) to start the white balance setup. [. . . ]