User manual PARADOX 646 KEYPAD

[. . . ] 616, 636 and 646 Keypads User's Manual TABLE OF CONTENTS 1. 0 BASIC OPERATION . . . . . . . . . . . . . . . . . . . . 2 2. 0 ACCESS CODES . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. 0 ARMING & DISARMING . . . . . . . . . . . . . . 6 4. 0 PANIC ZONES . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2) Enter the number of the zone(s) you wish to bypass. To "unbypass" a bypassed zone, enter the zone number of the bypassed zone. The [BYP] key will remain illuminated to indicate that there are bypassed zones. By using the "bypass recall" feature, you can reinstate the latest zone bypass instructions saved in memory. Press [BYP] in Step 2 (see above) and the previous bypass status will be re-established. 3. 9 FORCE (AWAY) ARMING To arm the system rapidly without waiting for the Esprit Keypads 9 "READY" light (for all zones to close), use Force "Away" arming. Open zones will not be protected, but will be armed as soon as they are closed. How do I Force Arm the system?1) Press the [AWAY] button and then enter your User Code. The [AWAY] key will flash. 3. 10 ARMING BOTH SYSTEMS SIMULTANEOUSLY If your code has access to both systems: How do I Arm Systems A and B simultaneously?The "ready" light will also begin to flash and the exit timer will begin to countdown. 3. 11 ARMING SYSTEM A AND B SEPARATELY If your Access Code has access to System A: How do I arm System A?The "ready" light will also begin to flash and the exit timer will begin to countdown. If your Access Code has access to System B: 10 User's Manual How do I arm System B?The "ready" light will also begin to flash and the exit timer will begin to countdown. 3. 12 STAY ARMING SYSTEM A Please refer to section 3. 3 on page 7 for an explanation of stay arming. Press the [STAY/11] key steadily for 2 seconds. With your system partitioned, only System A will be Stay armed when the [STAY/11] key is pressed. 3. 13 "NO MOVEMENT" SUPERVISION FEATURE Your panel can be programmed to send a report and/ or arm the system if it is not armed and there is no zone activity for a preprogrammed amount of time. 3. 14 AUTOMATICALLY ARM ON TIME Your installer can program your system to arm at a specific time each day. In this mode, all protected zones and detection devices must be in the "normal" state before arming can occur. Esprit Keypads 11 3. 15 DISARMING How do I Disarm the Security System?1) Enter through the designated entry/exit door. The keypad will beep and begin the entry delay timer. The "armed" light will go off and the keypad will stop beeping. 3. 16 DISARMING SYSTEM A AND B SEPARATELY If your Access Code has access to System A: How do I Disarm System A?1) Enter through the designated entry/exit door. The keypad will beep and begin the entry delay timer. 2) Press the [STAY] button and then enter a valid access code. The "armed" light will go off and the keypad will stop beeping. If your Access Code has access to System B: How do I Disarm System B?1) Enter the designated entry-exit door. The keypad will beep and begin the entry delay timer. [. . . ] To silence or reset a fire alarm, enter a valid user code. 18 User's Manual Note: IF A FIRE CONDITION EXISTS, FOLLOW YOUR EVACUATION PLAN IMMEDIATELY!If there is no fire condition, contact your monitoring company without delay to avoid an unnecessary response. Fire Safety in the Home Reasonable fire safety can be achieved by following a three point program: 1. Minimizing fire hazards (i. e. smoking in bed, etc. ) 2. Providing a fire warning system 3. Having and practicing an escape plan Providing a Fire Warning System Household fires are especially dangerous at night. [. . . ]