User manual PARKSIDE PWS 230 SE

[. . . ] pWS 230 Se Operation and Safety Notes ANGLE GRINDER 6 Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the device. GB / IE / CY Operation and Safety Notes Page 5 1 2 12 3 11 4 5 6 7 8 9 10 a b 4 C 17 D 18 e F 20 19 G 13 14 15 H 0 1 16 3 Table of contents Introduction Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Features and equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Included items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Technical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6 6 7 7 7 7 8 8 9 10 11 11 12 12 12 12 13 General safety advice for electrical power tools 1. Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2. Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3. Personal safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4. [. . . ] Allow the cutting disc to reach full speed before carefully continuing with the cut. Otherwise the disc could snag, jump out of the workpiece or cause a kickback. e) Support boards or workpieces whilst cutting to reduce the risk of kickback caused by a jammed cutting disc. Large workpieces may bend under their own weight. The workpiece must be supported to both sides of the cutting disc and particularly near the cutting disc and at the workpiece edge. f) Be particularly careful when pocket cutting in existing walls or other areas where you cannot see what you are cutting into. The cutting disc plunged into the surface could cut through gas or water pipes, electricity cables or other objects and cause kickback. GB/IE/CY 11 General safety advice for electrical power tools Q Special safety advice for abrading using sandpaper Follow the manufacturer's recommendations for sanding sheet size. Sanding sheets that project beyond the backing pad could cause injury in addition to jamming, tearing of the sheet or kickback. J Do not use over-sized sanding sheets. J J Q Special safety advice for polishing has any loose parts, in particular the fastening cords. Tuck the fastening cords away or trim them. Loose fastening cords rotating with the attachment could catch your fingers or become trapped in the workpiece. J J Do not use the polishing bonnet if it J Q Special safety advice for working with wire brushes J a) Bear in mind that wire brushes lose pieces of wire during normal use. Do not overload the wires by applying too much pressure. Flying pieces of wire can very easily penetrate thin clothing and / or skin. b) Use a guard, if recommended, but make sure that the wire brush does not come into contact with the guard. The diameters of disc brushes and cup brushes can increase due to contact pressure and centripetal forces. J J J Safety advice for angle grinders J DANGEr OF ELECTrIC SHOCK!Do not operate the device if the mains lead or mains plug is damaged. Do not touch the mains lead if it becomes damaged or cut through while you are using the device. Pull the plug out of 12 GB/IE/CY J J the mains socket immediately and have the device repaired by a suitably qualified person or at your service centre. Do not operate the device if it is damp and do not use it in a damp environment. If you use the device outdoors, always connect it through a residual current device (rCD) with a maximum trip current of 30 mA. If using an extension lead, always use one that is approved for outdoor use. Do not suspend or carry the device by the mains lead. Always work with the mains lead leading away from the rear of the device. [. . . ] Do not allow any liquids to enter the device. Have the carbon brushes replaced only at the service centre or an accredited electrical equipment repair centre. The device requires no other maintenance. Clean the device frequently; for best results do this immediately after you have finished using it. [. . . ]