User manual PARTNER P 720 P.U.O.

[. . . ] GR TMHMANTIKETM ¶HPOºOPIETM ¢È·, ¿ÛÙ ÙÔ ÚÈv ·fi ÙË ¯Ú<ÛË Î·È ÊÏ¿ÍÙ ÙÔ ÁÈ· v· ÙÔ ÛÌ, ÔÏÂÂÛÙ ÛÙÔ Ì¤ÏÏÔv A. B. C. D. Partner oil 50 : 1 McCulloch oil 40 : 1 2T oil 25 : 1 1 ltr. 4 5 10 20 2% 20 cm3 80 100 200 400 2, 5% 25 cm3 100 125 250 500 4% 40 cm3 160 200 400 800 E. F. G. H. I. L. A SUMMARY CHART TO IDENTIFY THE CORRECT COMBINATION OF BAR/CHAIN - FILE/FILE HOLDER D TABELLA RIASSUNTIVA PER IL CORRETTO ABBINAMENTO BARRA/CATENA - LIMA/GUIDA- LIMA B TABLEAU RECAPITULATIF POUR LE CORRECT ACCOUPLEMENT CHAINE/GUIDE CHAINE LIME/PORTE LIME C TABELLE FÜR DIE KORREKTE KOMBINATION VON STANGE/KETTE - FEILE/FEILENFÜHRUNG E TABLA PARA EL CORRECTO ACOPLAMIENTO DE LA CADENA/BARRA DE GUÍA - LIMA/GUÍA DE AFILADO F OVERZICHTSTABEL VOOR EEN CORRECTE STANG/KETTING - VIJL/VIJLLEIDER VERBINDING s SAMMANFATTANDE TABELL FÖR RÄTT KOMBINATION STÅNGE/KEDJA FIL/FILFÖRARE q GENOPTAGENTE LISTE TIL KORREKT SAMMENFÖJNING/ KÆDE-FIL/FÖLGERFIL v OIKEAN YHDISTELMÄN TAULIKKO PUTKI/KETJU - HÖYLÄ/HÖYLÄTÄSO { SAMMENFATTENDE TABELL FOR KORREKT SAMMENKOBLING AV STANG/KJETTING - FIL/FILSKINNE p TABELA RESUMIDA PARA O CORRETO EMPARELHAMENTO BARRA/CORRENTE - LIMA/GUIALIMA k / - / TÁBLÁZAT A VÁZ/LÁNCÉS RESZELÖ/RESZELÖVEZETÖ KORREKT KOMBINÁCIÓIHOZ PRO MAC 72 18"/45cm 68T 3/8" 225735 B 225739 B 86826B (7/32") 225736 B 225740 B 86826B (7/32") 225737 B 225740 B 86826B (7/32") 241366 241367 86826B (7/32") 241368 241369 86826B (7/32") 20"/50cm 72T 3/8" 20"/50cmSP 72T 3/8" 24"/60cmSP 82T 3/8" 28"/70cmSP 92T 3/8" g Due to a constant product improvement programme, the factory reserves the right to modify technical details mentioned in this manual without prior notice. i La casa produttrice si riserva la possibilità di variare caratteristiche e dati del presente manuale in qualunque momento e senza preavviso. f La Maison se réserve la possibilité de changer des caractéristiques et des données de ce manuel à n'importe quel moment et sans préavis. [. . . ] Pull the starter rope until the engine starts. Allow engine to warm up for a few seconds, holding the saw firmly. Release the safety lock by pressing the throttle trigger (B). The engine is stopped by moving the ignition switch to STOP position. After lengthy use of the chain saw at full speed, we recommend to run the engine for a few seconds at idle speed before stopping it. STARTING A WARM ENGINE Check that the ignition switch is not in the "stop" position and do not use the throttle lock. Hold the saw firmly, press valve (D) for decompression and pull the starter rope. STARTING A WARM ENGINE AFTER FUELLING In the fuel tank as run completely dry, procede to start as with a cold engine. 5 F USAGE IMPORTANT. Before using a chain saw read carefully the Operator's Manual and all safety precautions carefully. - Make sure that there are no bystanders or animals in the work area. - Study the direction of the fall of the tree and then plan your exit path away from the planned direction of fall. - Don't fell trees when there is a strong wind. 1 Clear the tree base of interfering limbs and brush. Clean the work area from stones or other objects which could damage the chain. If the tree has large protruding roots, remove them before felling (see illustrations). 2 A) Cut a felling notch (A) of 45°on the side you want the tree to fall to a depth of about one third of the trunk diameter (d). Then make a felling cut (B) about 5 cm higher than the felling notch on the opposite side of the tree. Make sure that the felling cut does not go right through the trunk. A hinge (C) must always be left to provide control over the direction of the fall. B) Use wedges to control the moment and direction of the fall. 3 When the tree starts to fall, walk away along your preplanned escape path. For limbing and bucking leave the lower limbs to support the log off the ground. [. . . ] Denne typeprøvningen fastslo at maskinen tilfredstiller de nødvendige helse- og sikkerhetskravene i EU Maskindirektiv. 000001 99999 L Intyg angående överenstämmelse med EG I enlighet med EGs Maskindirektiv (89/392/EEC, modifierat i 91/368/EEC), 93/68/CEE (CE märkningsdirektiv) & 89/336/CEE (Elektromagnetisk kompatibilitet). Undertecknad Pino Todero, auktoriserad av E. O. P. I. , intygar att bensindrivna kedjesågar: PM 72 cc med 45/50/60/70 cm långt svärd, vars serienummer visas ovan, tillverkade av E. O. P. I. , Via Como 72, 23868 Valmadrera (LC), Italia, överenstämmer med den maskin som var föremål för EG-provning i enlighet med Annex VI av Maskindirektivet. EG-provet utfördes av Marchio di Qualità (IMQ), Via Quintiliano 43, 20138 Milano (Italia), EG-provets certifikatsnummer IMQ AS 068 DM. Denna provningsmetod fastställer att maskìnen överenstämmer med de väsentliga hälso- och säkerhetsföreskrifterna i EGs Maskindirektiv. : EF Konformitetserklæring I overensstemmelse med EF Maskindirektivet (89/392/EEC, ændret ved 91/368/EWG), 93/68/EEC (CE mærkningsdirektiv) & 89/336/EEC (EMC-direktiv). [. . . ]