User manual PARTNER 421SEL

[. . . ] ELECTRIC WHEELED ROTARY LAWNMOWER ROTARY LAWNMOWER ELEKTRISCHER SICHELMÄHER MIT RÄDERN TONDEUSE ELECTRIQUE POUSSEE ELEKTRISCHE ROTERENDE GRASMAAIMACHINE OP WIELEN ELEKTRISK, HJULGÅENDE ROTORKLIPPER SÄHKÖKÄYTTÖINEN PYÖRILLÄ VARUSTETTU RUOHONLEIKKURI VARUSTETTU ELEKTRISK GLÄSKLIPPARE MED HJUL GLÄSKLIPPARE ELDREVET ROTORPLÆNEKLIPPER PÅ HJUL CORTACÉSPED ROTATIVO ELÉCTRICO A RUEDAS CORT ROTA MÁQUINA DE CORTAR RELVA ROTATIVA ELÉCTRICA COM RODAS CORT RELV ROTATIVA TOSAERBA ELETTRICO CON RUOTE A1 A2 B1 B2 C1 C2 D1 D2 D3 E F G1 B A 37cm & 42cm 37cm 42cm G2 H J1 J2 J3 42cm K1 K2 K3 CH CH CH L1 L2 L3 M1 M2 M3 N P1 P2 P3 Q1 3 2 1 Q2 Q3 Q4 Q5 Q6 Q7 R S 37cm T U V 42cm Safety Precautions Please Note :- This manual covers various products. Please read the user instructions carefully to fully identify, assemble and use the features that apply to your electric wheeled rotary lanwmower If not used properly this lawnmower can be dangerous!This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. The operator is responsible for following the warning and safety instructions in this manual and on the lawnmower. [. . . ] (B2) Note: The screw will form its own thread Lower Handles - 42cm (C1, C2) 1. If your product has Cutting Height with levers, ensure the lever is at the Highest Cut Height before following steps 2 & 3. Insert each side of the lower handles into deck as shown in Fig C1. Push each side of the handle firmly down until it is located securely into the deck (C2). Insert screw through the washer and into holes using a pozidrive screwdriver and tighten fully into deck as shown in Fig C2. Upper Handles 1. The upper handle should be fixed to the lower handle using whichever type of kit is provided as shown in Figs D1, D2 and D3. Fit the cables to the handles with the cable ties provided, making sure the cables are not trapped between the upper and lower handles. Grassbox Assembly Grassbox Assembly - 37cm. Insert the grassbox handle into the top of one of the grassbox halves. Press firmly down and forward until the handle clicks into position (E) 2. Turn the grassbox half over and insert screw into hole (as illustrated in fig E) and tighten fully. Locate grassbox upper into grassbox lower. (F) Align clips, ensure all clips are correctly located. Ensure all clips are securely connected. Insert the grassbox handle into the top of one of the grassbox halves. Press firmly down and forward until the handle clicks into position (E) 2. Turn the grassbox half over and insert screw into hole (as illustrated in fig E) and tighten fully. Position the two grassbox halves together and press each location point (G1-A) into position without fully connecting the clips. When the location points are matched correctly firmly press the grassbox together until all clips are securely connected. (G1-B, G2) 37cm, 42cm 1. To attach the grassbox to your lawnmower, lift the safety flap (H) and make sure the discharge chute is clean and free from debris. Locate fully assembled grassbox onto 2 location points at the rear of the deck. Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. [. . . ] * This guarantee is additional to, and in no way diminishes the customers statutory rights. Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine: Failures not covered by guarantee * Replacing worn or damaged blades. * Failures as a result of not reporting an initial fault. * Failures as a result of sudden impact. [. . . ]