User manual PEAVEY CLASSIC 410E DATASHEET

[. . . ] If both inputs are used simultaneously, the output levels are the same (both are Low Gain). The final level adjustment should be made after the desired sound has been achieved. The "out" position allows the Body control to function at a higher frequency, and the "in" position selects a lower frequency. REVERB LEVEL (19) The Reverb level control determines the amount of delayed (reverb) signal mixed back into the output. [. . . ] It is not advisable to remove the ground pin under any circumstances. If it is necessary to use the equipment without proper grounding facilities, suitable grounding adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles. 3V RMS) when "out" and 0 dBV (1 V RMS) when "in. " POWER AMP INPUT (30) Used to connect Line Level signal to the power amplifier. PREAMP OUT (31) The preamp out can be used to route the amplified signal to a mixing console, tape recorder, etc. connect the preamp output using a shielded cable to an input of the tape recorder , mixer , etc. This patch does not affect the operation of the amplifier. When using remote footswitch, always insert the plug fully (second click) to ensure proper operation. Dynamics @ 100% 130 W RMS into 8 ohms 220 W RMS into 4 ohms Power @ Clipping: (typically) (5% THD, 1 kHz, 120 V AC line) 130 W RMS into 8 ohms 220 W RMS into 4 ohms Frequency Response: +O, 3 dB, 60 Hz to 20 kHz, @ 100 W RMS into 8 ohms Hum 81 Noise: Greater than 86 dB below rated power Power Consumption: Domestic: 600 W @ 60 Hz, 120 VAC Export: 600 W @ 50/60 Hz, 220-2301240 V AC PREAMP SECTION The following specs are measured @ 2 kHz with the controls preset as follows: Push Bright, Off (out) Channel Select Normal (out) Low& High @ IO Mid @ 0 Resonance & Presence @ 0 dB Pre & Post Gain @ IO Gain 6: Thrash, Off (out) Normal Levels are with normal volume @ 5 Minimum Levels are with normal volume @ IO Shift, Off (out) Bottom, Body, & Edge @ 0 T-Dynamics @ 100% (Switching jack provides preamp output to power amp input connection when not used) System Hum & Noise @ Nominal Input Level: (20 Hz to 20 kHz un weigh ted) 72 dB below rated power Equalization: Special Low, Mid, & High passive type EQ Special Bottom, Body, & Edge EQ Push Bright: +6 dB @ 2 kHz Push Shift: Shifts Ultra Channel Body Frequency Push Thrash: -20 dB notch @ 1 kHz in Lead channel Push Gain: Increases Lead or Ultra gain Resonance: +6 dB @ cabinet resonance Presence: +6 dB @ 5 kHz External Footswitch Functions: Lead/Ultra Select (when Channel Select button is in) Clean Bypass Effects Loop Bypass Dimensions 81 Weight: 20. Due to our efSorts, for constant improvements, , feutures and specifications LiJ ted herein are subject to charge without notice. Completion and mailing of WARRANTY REGISTRATION CARDS - Should notification become necessary for any conditron that may require correction, the REGISTRATION CARD will help ensure that you are contacted and properly notified. Notice of address changes - If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of the change of address so as to facilitate your receipt of any bulletins or other forms of notification which may become necessary in connection with any condition that may require dissemination of information or correction. WARNING: When using electric products, basic cautions should always be followed, including the following. Read all safety and operating instructions before using this product. All safety and operating instructions should be retained for future reference. This product should not be used near water, i. This product should be located so that its position does not interfere with its proper ventilation. It should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air. This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. Never break off the ground pin on the power supply cord. [. . . ] Anything has fallen or been spilled into the unit. The unit has been dropped or the enclosure damaged. The user should not attempt to service this equipment. All service work should be done by a qualified service technician. [. . . ]