User manual PEAVEY DEP 800

[. . . ] Connections are made using a four-pin Neutrik® Speakon® or a paralleled two-position terminal block for additional cabinets. The SSE 15 incorporates flying points on the top and bottom for the utilization of the Peavey VersaMount 70 mounting bracket. The SSE 15 is constructed with a special grade of high density 13 mm birch plywood and covered with a durable acrylic polyurethane. [. . . ] This finish makes the enclosure presentable in any application. The SSE 15 is available in black, white or a natural wood finish for staining or painting. The SSE 15 is engineered for public address and a wide range of musical applications. · Mounting point for VersaMountTM 70 bracket · 13 mm birch plywood construction Frequency response, 1 meter on-axis, swept-sine in anechoic environment: 74 Hz to 17 kHz (±3 dB) Features: · Two-way sound reinforcement enclosure · Designed for permanent install · Full-range, wide-band production from 74 Hz to 17 kHz · Available in three finishes: black, white or natural · Peavey Scorpion® Pro 1500+ 15" woofer with 2. 5" (64 mm) voice coil · Peavey 14XTTM titanium diaphragm compression driver · Sound GuardTM IV tweeter protection network · Seven flying points (six 3/8" for suspension and one 1/4" for angle adjustment) Usable low frequency limit (-10 dB point): 54 Hz Power handling: Full range: 500 Watts program 1, 000 Watts peak Sound pressure level, 1 Watt, 1 meter in anechoic environment: Full range: 98 dB SPL (2. 83 V input) Maximum sound pressure level (1 meter): Full range: 122 dB SPL continuous 128 dB SPL peak Radiation angle measured at -6 dB point of polar response: 500 Hz to 1. 6 kHz: Horiz. 95° ± 30° 1. 6 kHz to 5 kHz: Horiz. 60° ± 35° 5 kHz to 16 kHz: Horiz. 40° ± 10° finished with a textured acrylic polyurethane. Also includes a full-length metal grille covered with acoustical grade grille cloth. Available in black, white or natural finishes. Mounting provisions: (6) 3/8"-16 threaded mounting suspension points (three each top and one each side and back). The frequency response of the SSE 15 is measured at a distance of 1 meter using a 1 Watt (into the nominal impedance) swept-sine input signal. As shown in figure 1, the selected drivers in the SSE 15 combine to give a smooth frequency response from 74 Hz to 17 kHz. Harmonic distortion: 1% rated power Second harmonic: 100 Hz: 2. 81% 1 kHz: 0. 13% Third harmonic: 100 Hz: 1. 0% 1 kHz: 0. 18% 10% rated power Second harmonic: 100 Hz: 8. 91% 1 kHz: 0. 56% Third harmonic: 100 Hz: 5. 62% 1 kHz: 0. 32% Architectural and Engineering Specifications The loudspeaker system shall have an operating bandwidth of 74 Hz to 17 kHz. The nominal output level shall be 98 dB when measured at a distance of one meter with an input of one Watt. The maximum program power handling shall be 500 Watts with a peak power input of at least 1000 Watts and a minimum amplifier headroom of 3 dB. The nominal radiation geometry shall be 90° in the horizontal plane and 40° in the vertical plane. The outside dimensions shall be 27" high by 18" wide by 17. 75" deep. The loudspeaker system shall be a SSE 15 model. Directivity Beamwidth is derived from the -6 dB points from the polar plots (see figure 3) which are measured in a whole-space anechoic environment. Q and Directivity Index are plotted for the on-axis measurement position. [. . . ] The loudspeaker system shall be a SSE 15 model. Directivity Beamwidth is derived from the -6 dB points from the polar plots (see figure 3) which are measured in a whole-space anechoic environment. Q and Directivity Index are plotted for the on-axis measurement position. These are specifications that provide a reference to the coverage characteristics of the unit. [. . . ]