User manual PEAVEY DESTINY

[. . . ] This lightweight speaker system is ideal for smaller venues where space is at a premium. Connections are made using a four-pin Neutrik® Speakon® or a paralleled two-position terminal block for additional cabinets. The SSE 12 incorporates flying points on the top of the unit and mounting points on the bottom for utilizing the Peavey VersaMount 70 mounting bracket. [. . . ] The SSE 12 incorporates flying points on the top of the unit and mounting points on the bottom for utilizing the Peavey VersaMount 70 mounting bracket. The SSE Series is available in black, white and natural finishes. Features: · Two-way sound reinforcement enclosure · Designed for permanent install · Available in three finishes: black, white or natural · Peavey Scorpion® Pro 1200+ 12" woofer with 2. 5" (64 mm) voice coil · Peavey 14XTTM titanium diaphragm compression driver · Sound GuardTM IV tweeter protection network · Seven flying points (six 3/8" for suspension and one 1/4" for angle adjustment) · Mounting point for VersaMountTM 70 bracket · 13 mm birch plywood construction · 500 Watts program/1000 Watts peak power handling · 79 Hz to 17 kHz · 98 dB at 1W/1m · 8 Ohms Frequency response, 1 meter on-axis, swept-sine in anechoic environment: 79 Hz to 17 kHz (±3 dB) Usable low frequency limit (-10 dB point): 60 Hz Power handling: Full range: 500 W program 1, 000 W peak Sound pressure level, 1 Watt, 1 meter in anechoic environment: Full range: 98 dB SPL (2. 83 V input) Maximum sound pressure level (1 meter): Full range: 122 dB SPL continuous 128 dB SPL peak Radiation angle measured at -6 dB point of polar response: 500 Hz to 1. 6 kHz: Horiz. 120° ± 30° 1. 6 kHz to 5 kHz: Horiz. 70° ± 25° 5 kHz to 16 kHz: Horiz. 40° ± 10° polyurethane with a full length metal grille covered and acoustical-grade grille cloth. Available in black, white or natural finishes. Mounting provisions: (6) 3/8"-16 threaded mounting suspension points (three each top and one each side and back). Use only forged shoulder machinery eye bolt, Mil Spec MIL51937-3. (1) 1/4"-20 threaded mounting point on back bottom for angle adjustments. The maximum program power handling shall be 500 Watts with a peak power input of at least 1000 Watts and a minimum amplifier headroom of 3 dB. The nominal radiation geometry shall be 90° in the horizontal plane and 40° in the vertical plane. The outside dimensions shall be 24. 5" high by 17. 43" wide by 13. 20" deep. The loudspeaker system shall be a model SSE 12. Directivity Beamwidth is derived from the -6 dB points from the polar plots (see figure 3) which are measured in a whole space anechoic environment. Q and Directivity Index are plotted for the on-axis measurement position. These specifications provide a reference to the coverage characteristics of the unit and provide insight into proper placement and installation in the chosen environment. The blending of the components of the SSE 12 exhibit a desirable beamwidth and directivity (figures 3 & 4) suitable for sound reinforcement applications. Electro-acoustic crossover frequency (internal passive): 2. 8 kHz Impedance (Z): Full range: Nominal: Minimum: 8 5. 1 3 + 2 YEAR LIMITED WARRANTY NOTE: For details, refer to the warranty statement. Copies of this statement may be obtained by contacting Peavey Electronics Corporation, P. O. [. . . ] These specifications provide a reference to the coverage characteristics of the unit and provide insight into proper placement and installation in the chosen environment. The blending of the components of the SSE 12 exhibit a desirable beamwidth and directivity (figures 3 & 4) suitable for sound reinforcement applications. Electro-acoustic crossover frequency (internal passive): 2. 8 kHz Impedance (Z): Full range: Nominal: Minimum: 8 5. 1 3 + 2 YEAR LIMITED WARRANTY NOTE: For details, refer to the warranty statement. Copies of this statement may be obtained by contacting Peavey Electronics Corporation, P. O. [. . . ]