User manual PEAVEY DETONATOR AX

[. . . ] This lightweight speaker system is ideal for smaller venues where space is at a premium. Connections are made using a four-pin Neutrik® Speakon® or paralleled two-position terminal block for additional cabinets. The SSE 10 incorporates flying points on the top of the unit and mounting points on the bottom for utilizing the Peavey VersaMount 70 mounting bracket. [. . . ] The SSE 10 incorporates flying points on the top of the unit and mounting points on the bottom for utilizing the Peavey VersaMount 70 mounting bracket. The SSE series is available in black, white and natural finishes. Features: · Two-way sound reinforcement enclosure · Designed for permanent install · Available in three finishes: black, white or natural · Premium 10" woofer · Peavey 14XTTM titanium compression driver · Sound GuardTM IV tweeter protection network · Seven flying points (six 3/8" for suspension and one 1/4" for angle adjustment) · Mounting point for VersaMountTM 70 bracket · 13 mm Birch plywood construction · 400 Watts program/800 Watts peak power handling · 80 Hz to 17 kHz · 95 dB at 1W/1m · 8 Ohms Frequency response, 1 meter on-axis, swept-sine in anechoic environment: 80 Hz to 17 kHz (±3 dB) Usable low frequency limit (-10 dB point): 60 Hz Power handling: Full range: 400 W program 800 W peak Sound pressure level, 1 Watt, 1 meter in anechoic environment: Full range: 95 dB SPL 2. 83 V input) Maximum sound pressure level (1 meter): Full range: 118 dB SPL continuous 124 dB SPL peak Radiation angle measured at 6 dB point of polar response: 500 Hz to 1. 6 kHz: Horiz. 130° ± 15° 1. 6 kHz to 5 kHz: Horiz. 75° ± 30° 5 kHz to 16 kHz: Horiz. Available in black, white or natural finishes. Mounting provisions: (6) 3/8"-16 threaded mounting suspension points (three each top and one each side and back). Use only forged shoulder machinery eye bolt, Mil Spec MIL51937-3. (1) 1/4"-20 threaded mounting point on back bottom for angle adjustments. (4) 1/4"-20 threaded mounting points on bottom to accommodate use of VersaMountTM 70 adjustable mounting bracket. The maximum program power handling shall be 400 Watts with a peak power input of at least 800 Watts and a minimum amplifier headroom of 3 dB. The nominal radiation geometry shall be 90° in the horizontal plane and 60° in the vertical plane. The outside dimensions shall be 19. 63" high by 15. 09" wide by 12. 12" deep. The loudspeaker system shall be a model SSE 10. Directivity Beamwidth is derived from the -6 dB points from the polar plots (see figure 3), which are measured in a whole space anechoic environment. Q and Directivity Index are plotted for the on-axis measurement position. These specifications provide a reference to the coverage characteristics of the unit and provide insight into proper placement and installation in the chosen environment. The blending of the components of the SSE 10 exhibit a desirable beamwidth and directivity (figures 3 and 4) suitable for sound reinforcement applications. Electro-acoustic crossover frequency (internal passive): 2. 1 kHz Impedance (Z): Full range: Nominal: Minimum: 3 + 2 YEAR LIMITED WARRANTY NOTE: For details, refer to the warranty statement. Copies of this statement may be obtained by contacting Peavey Electronics Corporation, P. O. [. . . ] These specifications provide a reference to the coverage characteristics of the unit and provide insight into proper placement and installation in the chosen environment. The blending of the components of the SSE 10 exhibit a desirable beamwidth and directivity (figures 3 and 4) suitable for sound reinforcement applications. Electro-acoustic crossover frequency (internal passive): 2. 1 kHz Impedance (Z): Full range: Nominal: Minimum: 3 + 2 YEAR LIMITED WARRANTY NOTE: For details, refer to the warranty statement. Copies of this statement may be obtained by contacting Peavey Electronics Corporation, P. O. [. . . ]