User manual PEAVEY ULTRA

[. . . ] The red LED will illuminate indicating power is being supplied to the unit. sTANDBY SWITCH (2) Allows amp to be placed in Standby or Active mode. In Standby mode the tubes remain hot but the amplifier is not operational. [. . . ] It is not advisable to remove the ground pin under any circumstances. If it is necessary to use the equipment without proper grounding facilities, suitable grounding adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit is operated with properly grounded receptacles. POWER AMPLIFIER SECTION Four 6L6GCs with 12AX7 driver Rated Power & Load: 120 W RMS into 16, 8, or 4 ohms Power @ Clipping: (typically @ 5% THD, 1 kHz, 120 VAC line) 130 W RMS into 16, 8, or 4 ohms (Bias must be reduced to measure) Frequency Response: +0, -2 dB 50 Hz to 20 kHz @ 100 W RMS into 8 ohms Hum 81 Noise: Greater than 76 dB below rated power Power Consumption: Domestic: 400 W, 50/60 Hz, 120 V AC Export: 400 W, 60 Hz, 220-230/240 V AC Dimensions & Weight: 11 . The following specs are measured @ 1 kHz with the controls preset as follows: Low & High EQ @ 10, Mid EQ @ 0 Bright out Ultra & Crunch Posts @ IO Gain switches out Bottom, Body, & Edge @ 0 dB Reverb level @ 0 Master level @ 10 (Nominal levels are with Pre Gain @ 5. O mV RMS Preamp Low Gain Input: (-6 dB Pad) Impedance: High-Z, 44 K ohms (all levels are increased by +6 dB) Effects Send: Load Impedance: 47 K ohms or greater Nominal Output: -10 dBV, 300 mV RMS Effects Return: Impedance: Very High-Z, 470 K ohms Designed Level: -10 dBV, 300 mV RMS Preamp Output: Load Impedance: 47 K ohms or greater Nominal Output: +I0 dBV, 3 V RMS Remote Footswitch: Special 3-button unit with LED indicators (supplied) System Hum & Noise @ Nominal Level: (Clean channel - 20 Hz to 20 kHz unweighted) Greater than 74 dB below rated power (Special noise gate circuitry for Ultra & Crunch) Equalization: (clean channel on/y) Custom Low, Mid, & High passive type EQ Push Bright: +6 dB @ 2 kHz Voicing: (U/tra & Crunch channels only) Active Bottom, Body, & Edge EQ Push Gain: Increases gain in Ultra & Crunch channels Tone settings given are general and will vary according to the type of guitar, gauge type of the strings, the type of pickup, and even the type of pick. Personal preference, playing style, and type of music greatly contribute to desired tonality. STANDBY SWITCH (Interrupteur de condicih de espera) (2) Este interruptor le permite a su aparato estar en condition de "espera" o la condition de active. Rbglez n'importe quelle valeur de modification du signal & I'aide des trois canaux de I'amplificateur: clean (non traite), crunch (croquant) et dirty (sale), et passez de I'un 2 I'autre g I'aide du panneau avant ou de la pedale. Wtihlen Sie jeden Verstarkungsgrad in clean (Klarton), crunch (mittelstarke Verzerrung) oder dirty (starke Verzerrung) mit dem 3-Kanal-Verstarker, und schalten Sie von einem Kanal zum anderen, entweder am Schaltbord oder mit der FuOpedale. PEAVEY ONE-YEAR LIMITED WARRANTY/REMEDY PEAVEY ELECTRONICS CORPORATION ("PEAVEY") warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in material and workmanship for a period of one (1) year from date of purchase, PROVIDED, however, that this limited warranty is extended only to the condltlons, exclusions, and limitations hereinafter set forth: subject original purchaser PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanship for a period df ninety (90) days from date of purchase- PROVIDED, however, that this limited warranty is extended only to the onginal retail purchaser and IS also subject conditions, exclusions. The first purchase of the product is for the purpose of resale; or b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER; or c. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not arising out of defects in material or workmanship; or d. the serial number affixed to the product is altered , defaced , or removed. In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will: a. , cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect in material or workmanship or replace the product, at Peavey's option; and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the purchaser. sHOULD BE ACCURATELY COMPLET ED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) THE WARRANTY REGISTRATION DAYS FROM THE DATE OF YOUR PURCHASE. [. . . ] Never break off the ground pin on the power supply cord. For more information on grounding, write for our free booklet "Shock 9. Power supply cords should always be handled carefully. [. . . ]