User manual PEAVEY UMA 352 DATASHEET

[. . . ] Specifications UMATM 352 MIXER/AMPLIFIER Specifications Rated output power: 35 Watts Output regulation: Direct out: Transformer out: <0. 5 dB <1. 0 dB Pre out: Inputs: Channel 1: 1 V nom. ; +21 dBu max. at 100 Ohms Mic 1 mV at 1. 8 k Ohms (XLR or screw terminals) Tel 100 mV at 20 k Ohms (Screw terminals) Mic 1 mV at 1. 8 k Ohms (Screw terminals) Line 100 mV at 20 k Ohms (Screw terminals) Line 100 mV at 20 k Ohms (Screw terminals) Line 100 mV at 20 k Ohms (Screw terminals) Stereo 316 mV (-10 dBV) at 4. 0 k Ohms (RCA jacks) 1 Volt at 20 k Ohms Frequency response: Power Amplifier: ±0. 5 dB, 20 Hz to 20 kHz, direct out ±1. 0 dB, 50 Hz to 20 kHz, transformer out Preamplifier: ±1. 0 dB, 20 Hz to 20 kHz THD: Power Amplifier: Preamplifier: Power bandwidth: Direct out: Transformer out: 0. 05% (1 kHz) 0. 10% with nominal gain settings <10 Hz to 70 kHz 30 Hz to 40 kHz Channel 2: Channel 3: Channel 4: Signal/noise: (22 Hz -- 22 kHz) typical All controls CCW: -100 dB All controls nominal (5): -90 dB Level controls CCW and master level CW: -80 dB Outputs: Direct out: XFMR: Ch. [. . . ] Channels 3 and 4 shall be electronically balanced line-level inputs with Channel 4 including stereo RCA jacks. Additionally, the output from Channel 4 input shall be made available via an electronically balanced output with a Eurotype connector and a separate level control. The module port shall be capable of controlling both mute buses. Depending upon the module chosen, it can be set up for master configuration. When the input signal to an input module commands a mute function, Channels 1-4 shall be muted. Only Channel 1 shall have a continuously variable mute threshold control on the rear panel. Setting this control fully clockwise shall defeat the Channel 1 mute function. The mute level threshold for Channel 1 shall be increased as the control is turned clockwise. When the signal level in Channel 1 exceeds the mute threshold, Channels 2-4 shall be muted. Channels 1 and 2 shall include a switch to defeat its muting function. When the switch is out, the channel shall be muted. When the switch is in, the channel cannot be muted. [. . . ] A loop switch shall bypass the loop point. Remote master level control capability shall be included along with remote control for each mute bus. 4 GND +Vmod OUTP UTS 100V 70V 8 COM XFMR POWER SI GNAL ENAB LE BYPASS Power Switch SPS PA POWER SUPPLY AC Input LOOP EXT MUTE 1 PWR IN MASTER LEVEL CONTROL RV C PRE OUT V C SHD 2 LO LOW HIGH HI CH 4 OUT MU TE1 MU TE2 - + AC RECEPTACLE (120V UNIT ONLY) MASTER LEVEL +V MU TE2 THRESH DEFEA T MU TE1 ACTIVE INPUT LEVEL CH 2 LEVEL DEFEA T MU TE2 ACTIVE CH 1 LEVEL CH 3 LEVEL MUTE MUTE MUTE PREAMP PREAMP PREAMP MUTE SI GNAL SI GNAL SI GNAL SENS SENS MIC TEL MIC 24V TEL CH 1 N I - + CH 2 N I LI NE CH 3 N I CH 4 N I + + SI GNAL MOD ULE PO RT CH 1 MIC +24V + PREAMP CH 4 LEVEL CH 4 OU T LEVEL Fuse STEREO IN L G - - - - MUTE 1 MUTE 2 IN GND MIC 24V OUT + R +Vfan +Vhi +Vlo -Vhi -Vlo N L Specifications UMATM 352 MIXER/AMPLIFIER UMATM 352 MIXER/AMPLIFIER FRONT UMATM 352 MIXER/AMPLIFIER BACK FUSE Peavey Electronics Corporation · 711 A Street · Meridian, MS 39301 601-483-5376 · Fax 601-486-1678 · http://aa. peavey. com ©2002 Printed in the U. S. A. [. . . ]