User manual PEAVEY XR 600B

[. . . ] For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable. This statement will be applied only for the printers marketed in U. S. A. Statement of The Canadian Department of Communications Radio Interference Regulations This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. [. . . ] 3 Do not pull the cover open lever and open the printer cover when printing is in progress or when the auto cutter is operating. 3 Do not pull out paper while the printer cover is closed. 3 If liquids, foreign objects (coins and paper clips), and so on enter the printer, turn off the printer, unplug it from the AC outlet, and contact your dealer for advice. Continued use could cause a short circuit, which may result in fire or electric shock. 3 Place the printer in a horizontal position when installing the paper, even if the model can be installed vertically. If the paper is installed with the printer in a vertical position, the printer will be unstable and could fall, which may result in injury. ­ 0 ­ 6. Control Panel and Other Functions 6-1. ControlPanel 1POWER lamp (Green LED) Lights when the power is ON. 2FEED button Press the FEED button to feed roll paper. 3ERROR lamp (Red LED) Indicates various errors in combination with POWER lamp. 2FEEDbutton 3ERRORlamp(RedLED) 1POWERlamp(GreenLED) 6-2. BasicIndicators Power On/Off No Error POWERlamp On/Off On ERRORlamp -- Off Buzzer -- -- ­ ­ 6-3. Errors ) Recoverable error ErrorDescription Paper end error POWERlamp On ERRORlamp Flashes (On: sec. / Off: sec. ) Buzzer 4 short beeps (0. (Refer to Section 6-4-. ) (Holding down for more seconds) () Adjusting the Dot Alignment Mode is entered by releasing the FEED switch after the buzzer sounds twice. (Refer to Section 6-4-. ) (Holding down for more seconds) () The Hexadecimal Dump Mode is entered by releasing the FEED switch after the buzzer sounds three times. (Refer to Section 6-4-. ) (Holding down for more seconds) (4) The Black Mark Sensor Alignment Mode is entered by releasing the FEED switch after the buzzer sounds four times. (Refer to Section 6-4-4. ) (Holding down for more seconds) (5) The Near End Sensor Adjustment Mode is entered by releasing the FEED switch after the buzzer sounds five times. (Refer to the separate Specifications Manual for details. ) (Holding down for more seconds) (6) The Memory Switch Manual Setting Mode is entered by releasing the FEED switch after the buzzer sounds six times. (Refer to the separate Specifications Manual for details. ) (Holding down for more seconds) () The Memory Switch Override Mode is entered by releasing the FEED switch after the buzzer sounds seven times. (Refer to the separate Specifications Manual for details. ) (Holding down for more seconds) Returns to (). ­ 4 ­ 6-4-1. SelfPrintingMode Self-printing will be performed to print the Ver. ASCII-printing will be repeated when the FEED switch is held continuously at the end of ASCII-printing. The self-printing mode will end automatically when the FEED button is released at the end of ASCII-printing. ­ 5 ­ 6-4-2. AdjustingtheDotAlignmentMode You may never have to use the procedure described in this section, but after you have been using your printer for some time you may find that the dots of some graphics do not align correctly. For example, what should look like: may come out looking like one of the following: orlikethis This is caused when mechanical parts of the printer get out of alignment. This happens only rarely and you may never experience it at all throughout the life of the printer. [. . . ] During self printing and dot alignment adjustment. When the printer stops printing due to a paper end or an optional paper near end. DTR OUT BUSY BUSY BUSY BUSY BUSY BUSY BUSY -- -- BUSY ­ 46 ­ PinNo. 0 SignalName DTR Direction OUT - 4 5 N. C. [. . . ]