User manual PEG PEREGO PRIMO VIAGGIO

[. . . ] € IMPORTANT: "Primo Viaggio tri-fix", group 0+, must be installed facing opposite to the normal forward movement of the car, on seats without airbags. Do not install “Primo Viaggio tri-fix” on seats that face backwards or sideways. • "Primo Viaggio tri-fix" has an “Adjustable Side Impact Protection System”: this offers improved protection against side impacts with the “simultaneous system” for headrestharness adjustment. € "Primo Viaggio tri-fix" is approved for installation in cars without a base support or with two types of base as required (the use of a seat base offers improved safety): "Adjustable Base" or "Isofix Base" (check that the vehicle is fitted with the Isofix system -a list of car models fitted with the system is provided with the product). [. . . ] Adjust the height and tension of the straps ensuring that they are snug to the child’s body without constricting him/her too much. Check that the harness is not twisted and that the child does not release it. € This car safety seat is not designed for extended periods of sleep. The safety seat is not a substitute for a cot and if the child needs to sleep it is important to lie him/her down. € Do not leave the car safety seat in the car exposed to the sun. Some parts might heat up and be harmful to the delicate skin of the child -check before placing the child in the seat. € Do not use the safety seat without its fabric covering, which cannot be replaced with one not approved by the manufacturer since it is an integral part of the safety seat and the safety system. € If in doubt refer to the manufacturer or retailer of the safety seat. € Do not remove the adhesive and stitched labels since this might make the product non compliant with legal requirements. € Do not use the safety seat if it has signs of breakage or missing parts, is second hand, or if it has been subjected to violent stress in an accident, because it might have suffered extremely dangerous structural damage. € For any repairs, replacement parts and information about the product, contact the after-sales assistance service. Contact information is provided on the last page of this manual. € Do not use this car safety seat after five years from the date of production indicated on the structure. The natural ageing of the materials may mean that it is no longer compliant with standards. € The use of the safety seat for premature infants born at less than 37 weeks could cause respiration problems for the infant seated in the safety seat. It is advisable to seek medical advice before leaving the hospital. € Do not use accessories not approved by the manufacturer or by the competent authorities. € To avoid the risk of falling, never place the safety seat on raised surfaces (tables, work surfaces) soft surfaces (beds, sofas) or sloping surfaces. € In the home do not use the car safety seat if the child is able to remain seated alone. Instructions for use 1• "Primo Viaggio tri-fix" is provided with the Ganciomatic System for in-car attachment and detachment from an "Isofix Base" or "Adjustable Base" and outside the vehicle to Peg-Pérego strollers and chassis. To attach "Primo Viaggio tri-fix" (to an "Isofix Base", "Adjustable Base", or Peg-Pérego stroller or chassis) align it with the attachment points and push down with both hands until it clicks into place. 2• To release "Primo Viaggio tri-fix" (from an "Isofix Base", "Adjustable Base", or Peg-Pérego stroller or chassis) raise the handle to the transport position, push the lever on the backrest upwards and at the same time raise the safety seat. [. . . ] 17• To remove the safety seat harness: • press the metal button in the centre of the seat to extend the safety harness braces; • press the red button on the crotch strap buckle to release the harness; • release the harness braces from the metal buckle on Instructions for in-car use the back of the safety seat and unthread them from the headrest and shoulder covers; • remove the two plastic covers on the back of the safety seat by levering with a standard tip screwdriver, and unthread the two side buckles and the central crotch strap buckle. 18• To remove and uncover the headrest: • remove the cover pulling it downwards and slide it carefully off the two side tabs; • unscrew the two headrest screws with a screwdriver, press the teeth on the slots and pull the headrest to release it. 19• To remove the padding: • slide off the four padding fixing tabs from the edge of the safety seat; • remove the two side guide covers for the car seat belt; • remove the metal button cover in the centre of the safety seat, releasing it from under the seat; • remove the padding. Padding cleaning instructions Cover removal 20• To refit the padding: • slide on the padding; • insert the four padding fixing wings on the edge of the safety seat; • reposition the metal button cover in the centre of the safety chair and engage it from under the chair; • position the two side guide covers for the car seat belt with the slots facing the inside of the safety seat and check that they are correctly engaged in position. [. . . ]