User manual PEG PEREGO SWITCHABLE

[. . . ] Com manuals search engine + VIAGGIO 0 SWITCHABLE E N Instructions for use KO 사용지침 UNIVERSAL CATEGORY 0-13 Kg Group 0+ BELTED OK NO NO NO NO NO E N• "Viaggio 0+1 Switchable" is fastened to the vehicle in a rear-facing position using the vehicle’s seatbelt when used as a Group 0+ car seat (from 0 to 13 Kg). Com manuals search engine UNIVERSAL CATEGORY 9-18 Kg Group 1 BELTED OK NO NO NO NO NO E N• "Viaggio 0+1 Switchable" is fastened to the vehicle in a forward-facing position using the vehicle’s seatbelt when used as a Group 1 car seat (from 9 to 18 Kg). Com manuals search engine 9 10 A A B B 11 12 Downloaded from www. Com manuals search engine B C A C C 13 14 15 16 Downloaded from www. [. . . ] 3• Install the “Viaggio 0+1 Switchable” car seat on the vehicle’s seat so that it is rear-facing, as shown in the figure. Pass the vehicle seatbelt between the frame and body of the car seat following these steps: - slip the belt into the light blue belt guides first (arrow A); - fasten the belt, ensuring that it clicks into place (arrow B); 4• Pass the seatbelt through the upper light blue belt slot (arrow C). IMPORTANT: Take hold of the seatbelt and pull it firmly, so as to ensure that the “Viaggio 0+1 Switchable” fits as close as possible to the vehicle seat (arrow D). 1• 18 Instructions for use UNIVERSAL CATEGORY - Belted Group 0+ Fastening with seatbelts IMPORTANT: For the correct use of the “Viaggio 0+1 Switchable” car seat in Group 1 mode, it is necessary to: - Reposition the casing within the base of the car seat. Press the lever and push inwards, as indicated in the figure. 6• Install the “Viaggio 0+1 Switchable” car seat on the vehicle’s seat so that it is front-facing, as shown in the figure. 7• To make it easier to pass the vehicle’s seatbelts through the back of the car seat, it is necessary to recline the car seat to its lowest position by operating the lever, as shown in the figure. 8• Pass the vehicle seatbelt between the frame and body of the car seat. 9• The waist strap must pass through the lower guides, marked in red; fasten the belt, ensuring that it clicks into place. 10• Tighten the waist strap, ensuring it has passed through the lower guides, marked in red. 11• Bring the car seat back into the upright position by pulling the handle below the seat (Fig. A) and pushing the car seat as shown in the figure (Fig. 12• To complete the installation process, use the Steady Fix device: open the clip and pass the diagonal strap through it, ensuring that it is taut and not twisted (Fig. 13• IMPORTANT: Take hold of the seatbelt and pull it firmly upwards, so as to ensure that the “Viaggio 0+1 Switchable” fits as close as possible to the vehicle seat (Fig. Once installed, the car seat may be reclined to the desired position (See Point 6). How to secure your child in the “Viaggio 0+1 Switchable” car seat 1 4• Before placing the child in the car seat, release the Downloaded from www. Com manuals search engine harness by pushing the red button on the crotch strap buckle. 15• Lift the harness and attach the buckles to the elastic bands on the sides. 16• Place the child in the car seat and arrange the harness over the child’s shoulders and waist, as shown in the figure. 17• Lock the harness by overlapping the tongues and inserting them into the buckle of the crotch strap until they click into place. 18• The child is now sitting correctly with the harness fastened properly. 19• Finally, tighten the shoulder straps until they are snug to the child’s body by pulling the central adjustment strap towards you, as shown in the figure, taking care not to over-tighten the straps. [. . . ] €¢ Fasten the harness at the front (point 17). iMPORTANT: The straps must not be twisted. 44• ATTENTION: The central adjustment strap must pass between the body and the plastic shield, as shown. How to read the type approval label • This paragraph explains how to interpret the type approval label (orange label). [. . . ]