User manual PENTAX 645 LS 75MM F/2.8-135MM F/4 LENS

[. . . ] is a sole proprietor of the PowerTopoLite software. The PowerTopoLite software and publication or parts thereof, may not be reproduced in any form, by any method, for any purpose. makes no warranty, expressed or implied, including but not limited to any implied warranties or merchantability or fitness for a particular purpose, regarding these materials and makes such materials available. CONTENTS COPYRIGHT CONTENTS DISPLAY AND KEYBOARD OPERATION KEY FUNCTION KEY DISPLAY COMBINATION OF MODE A OR MODE B ALPHANUMETRIC INPUT 1. INTRODUCTION 1. 1 Introduction 1. 2 Before using the PowerTopoLite manual ACCESSING THE POWERTOPOLITE 2. 1 How to access the PowerTopoLite 2. 2 Allocation of each PowerTopoLite Function key 2. 3 Typical Function keys of the PowerTopoLite FILE MANAGER 3. 1 Information of the remaining memory available 3. 2 Creation of a new Job 3. 3 Selection of a Job name 3. 3. 1 Selection of a Job 3. 3. 2 Selection by a Job name input 3. 4 Deletion of a Job name 3. 4. 1 Deletion from a Job list 3. 4. 2 Deletion from a Job name search 3. 5 All Clear MEASURE 4. 1 Station setup [By Rectangular Coordinates] 4. 1. 1 Point name, PN, input 4. 1. 2 Coordinates, X, Y, Z, IH, and PC input 4. 2 Station Orientation 4. 2. 1 Station orientation 4. 3 Measuring 4. 4 Point Code 4. 5 Remote, Offset, Station, H. [. . . ] ANGLE 000° 00' 00" CLEAR Input your desired value to view the RESULT OF COORD. The second point Coordinates are displayed by plus or minus from the known Coordinates. RESULT OF COORD. CALCULATE X Y Z +0. 000m +0. 000m +0. 000m ESC ENT Press [ENT] to view the following screen. RESULT OF COORD. PC: SAVE + XXXXXXXX. XXX m + XXXXXXXX. XXX m + XXXXXXXX. XXX m ACCEPT The PN, X, Y, Z and PC are viewed and can be edited. If all items are OK, press [F1][SAVE] or [F5][ACCEPT] to save them. 85 8. 1. 2. 2 Distance and H. angle In the same manner, the values of Distance and H. angle are inputted as follows and the second point Coordinates are displayed. POINTS COORDINATES 1. DI and press [ENT] to view DI screen. DISTANCE 0000. 000m CLEAR Input your desired value and press [ENT] to open the H. ANGLE 000° 00' 00" CLEAR 86 Input your desired value to view the RESULT OF COORD. The second point Coordinates are displayed by plus or minus from the known Coordinates. RESULT OF COORD. CALCULATE X Y Z +0. 000m +0. 000m +0. 000m ESC ENT Press [ENT] to view the following screen. RESULT OF COORD. You can see the coordinates of center point of the arc and the radius of the arc. RESULT OF CIRCLE RADIUS X Y Z RADIUS +0. 000m +0. 000m +0. 000m +0. 000m ESC ENT Press [F5][ENT] to save the coordinates of center point. RESULT OF CIRCLE RADIUS 1. PC: + XXXXXXXX. XXX m + XXXXXXXX. XXX m + XXXXXXXX. XXX m ACCEPT The PN, X, Y, Z and PC are viewed and can be edited. If all items are OK, press [F5][ACCEPT] to save them. 91 8. 1. 4 Line-Arc intersection Point1 Point 2 SP EP Center P Radius Two intersection points of one line and circle are calculated by this function. The circle is drawn by center point and radius. You can store two possible intersection points. Input: Line: start point and end point Arc: center point and radius Output: Two possible intersection points From the PowerTopoLite screen, press [F2][CALC] to view the CALCULATION screen. CALCULATION 1. REM 92 Select 1. COGO and press [ENT] to view the COGO screen. COGO 1. CIRCLE RADIUS and press [ENT] to view LINE-ARC INTERSECTION screen. LINE-ARC INTERSECTION 1. SP and press [ENT] to view SP screen. SP 1. PC: SAVE + 00000000. 000 m + 00000000. 000 m + 00000000. 000 m LIST ACCEPT Input PN (Point Name), X, Y, Z, and PC (Point Code) of SP point or import from the memory of rectangular coordinate as SP by [F2][LIST]. 93 If you finish the input of SP value, press [F5][ACCEPT]. Then you go to EP input screen. EP 1. [. . . ] Press [ENT] to select and press [F5][ACCEPT] to enter. PREFERENCE 5. FACTOR ACCEPT When "ALL IN ONE INFO"is selected, all information will be displayed on the result of stakeout panel. STAKEOUT PN PH D H. angle D V. angle DX DY DZ MEAS POT4 X. XXX m XXX° XX' XX" - X° XX' XX" + X. XXX m NEXT PAGE TARGET When "LARGE CHARACTOR"is selected, result information is shown with two screens and these screens and the Graphics screen can be switched by [ENT]. STAKEOUT PN PH D H. angle D V. angle D H. [. . . ]