User manual PENTAX AF200SA FLASH

[. . . ] When using the AC adapter, make sure that the DC terminal is properly connected to the camera. Operation is not guaranteed on all PCs meeting the system requirements. 57577 01-200509 Printed in Philippines Windows Step 2 Installing the Software Installing the Image Processing Software (ACDSee for PENTAX 2. 0) This section describes the procedures for installing ACDSee for PENTAX 2. 0, which lets you view and edit images transferred to your PC. · Windows Media Player 7. 1 or later must be installed in your PC to install ACDSee for PENTAX 2. 0. · When multiple accounts have been setup in Windows 2000 or Windows XP, log on with an account that has administrative rights before installing the software. 5 Macintosh Click [ACDSeeTM]. Follow the on-screen guidance and enter the registration information when the Setup screen appears. Reboot your PC after installation is finished (Other settings are not necessary during installation). Step 2 Installing the Software Installing the Image Processing Software (ACDSee for PENTAX) This section describes the procedures for installing ACDSee for PENTAX, which lets you view and edit images transferred to your Macintosh. 1 2 Turn your PC on. Insert the CD-ROM (S-SW32) into the CD-ROM drive. The PENTAX Software Installer screen appears. [. . . ] 2) Double-click the [CD-ROM drive (S-SW32)] icon. 3) Double-click [Setup. exe]. If QuickTime and DirectX are not installed in your PC, a message such as the one shown on the right appears when ACDSee for PENTAX 2. 0 is run. Click [Close] and install QuickTime and DirectX from the [PENTAX Software Installer] screen. 1 2 3 4 5 Turn your Macintosh on. Insert the CD-ROM (S-SW32) in the CD-ROM drive. Double-click the [Install ACDSee] icon. The PENTAX Software Installer screen appears. Double-click the [Master Installer] icon to display the PENTAX Software Installer screen. If QuickTime and DirectX are not installed in your PC, operation of ACDSee for PENTAX 2. 0 is not guaranteed. If your PC is running Windows Media Player earlier than version 7. 1, a message such as the one shown on the right may appear during installation. In this case, follow the instructions below to update Windows Media Player before installing the software. 1 Cancel installation of ACDSee for PENTAX. Click [Cancel] and then click [Finish] when the next screen appears. 2 Install the latest version of Windows Media Player. "Found New Hardware Wizard" is displayed. "Found New Hardware Wizard" is displayed. Follow this instruction Turn off the camera and remove the USB cable from your PC. Click "Cancel", turn off the camera and remove the USB cable from your PC. Click "Cancel", turn off the camera and remove the USB cable from your PC. Turn off the camera and remove the USB cable from your Macintosh computer. Turn off the camera and remove the USB cable from your Macintosh computer. Turn off the camera and remove the USB cable from your Macintosh computer. Disconnecting the Camera from Your PC For Macintosh user go to Macintosh Step 4 Windows XP 3 Turn your camera on. The Device Detector screen appears automatically. If the Device Detector screen does not appear, display and copy the images following the steps in "When the Device Detector screen does not appear". When the camera is connected to a PC with the USB cable, the power indicator blinks to indicate that the camera is communicating with the PC. 1 2 Double-click the in the task bar. [Safely Remove Hardware] icon The Safely Remove Hardware screen appears. Select [USB Mass Storage Device] and click [Stop]. The Stop a Hardware device screen appears. MacOS 9. 2 The i-Photo function starts, but the image cannot be identified. Nothing is displayed on the camera and your Macintosh computer. [. . . ] "Print error" is displayed on the camera's LCD monitor. The message "Software needed for the USB device "Unnamed device" is not available. Click "Cancel", turn off the camera and Would you like to look for the software on the remove the USB cable from your Macintosh internet?" appears on your Macintosh computer. computer. Transferring Images 4 Confirm that [Acquire images from the device with ACDSee] is checked and click [OK]. 3 Select [USB Mass Storage Device] and click [OK]. A message appears indicating that the hardware can be safely removed. 5 Click [Next]. 4 1 Disconnect the USB cable from your PC and the camera. Macintosh Step 4 Transferring Images Windows 2000/Me Transferring Images to a Macintosh Connecting the Camera and Macintosh 6 Select an image to copy and click [Next]. Double-click the in the task bar. [Unplug or eject hardware] icon 4 1 2 Specify the location to store the images, make sure that the [Launch ACDSee] checkbox is checked and click [Download]. The images are copied to Macintosh and the ACDSee for PENTAX browser opens when the copying is finished. [. . . ]