User manual PENTAX MICROSCOPE ADAPTER K

[. . . ] Images taken with the purpose of obtaining copyrights also cannot be used outside the scope of use of the copyright as laid out in the Copyright Act, and care should be taken here also. Regarding trademarks · PENTAX, Optio and smc PENTAX are trademarks of HOYA CORPORATION. ACDSee and the ACDSee logo are trademarks of ACD Systems Ltd. in Canada, the U. S. , Europe, Japan and other countries. [. . . ] Mode] menu appears. Use the four-way controller (23) to select [White Balance]. Press the four-way controller (5). The [White Balance] screen appears. 107 4 Use the four-way controller (23) to change the setting. You can check the results of available white balance settings on the preview image each time you press the four-way controller (23). White Balance Auto MENU Cancel OK OK 5 3 Taking Pictures Press the 4 button. The setting is saved. 6 Press the 3 button. The camera returns to capture status. Refer to the following "Manual Setting" for instructions on adjusting the white balance manually. If you change the [White Balance] setting frequently, you can save time by assigning it to the Green button (p. 117). Saving the White Balance setting 1p. 123 Manual Setting Have a blank sheet of white paper or similar material ready. 1 2 In the [White Balance] screen, use the four-way controller (23) to select K (Manual). Point the camera at the blank sheet of paper or other material so that it fills the frame displayed in the center of the screen. White Balance SHUTTER Adjust OK MENU Cancel OK 3 Press the shutter release button fully. The white balance is automatically adjusted. 108 4 5 Press the 4 button. The setting is saved and the screen returns to the [A Rec. Mode] menu. Press the 3 button. The camera returns to capture status. Setting the AE Metering You can set the area of the screen where the brightness is metered to determine the exposure. 3 Taking Pictures L M N Multi-segment metering Center-weighted metering Spot AE metering The camera divides the image into 256 areas, meters the brightness and determines the exposure. The camera takes a reading of the overall brightness of the picture with the center of the image having more influence on the exposure. The camera determines the exposure by metering the brightness only at the center of the image. 1 2 3 4 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [AE Metering]. Press the four-way controller (5). A pull-down menu appears. Use the four-way controller (23) to select the AE Metering setting. Rec. If you set Pixel Track SR, the camera automatically corrects any camera shake in the images you shot. The default setting is [Auto]. 1 2 3 4 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Pixel Track SR]. Press the (5) button. A pull-down menu appears. Use the four-way controller (23) to select [Auto] or [Off]. Auto Off Automatically corrects for camera shake. Mode Pixel Track SR Recorded Pixels White Balance Focusing Area AE Metering Sensitivity MENU Cancel 1/3 Auto 12M Off AWB Auto OK OK 5 Press the 4 button. The setting is saved. 6 Press the 3 button. The camera returns to capture status. Pixel Track SR does not function in the following situations: - When C (Half-length Portrait), N (Frame Composite), X (Digital Wide) or F (Digital Panorama) is selected as the shooting mode - When g (Self-timer), j (Continuous Shooting) or K (Burst Shooting) is selected as the drive mode - When the flash discharges - When the sensitivity is set to 1600 or higher - During Movie or Voice Recording 3 Taking Pictures Setting the Instant Review Use this setting to specify whether or not an Instant Review is displayed immediately after images are shot. The default setting is [1sec. ] (displays the image for 1 second). 1 2 3 4 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Instant Review]. Press the four-way controller (5). A pull-down menu appears. Use the four-way controller (23) to select [1sec. ] or [Off]. 1sec. Off Instant Review is displayed for 1 second. Instant Review is not displayed. Rec. Mode EV Compensation Movie Blink Detection Digital Zoom Instant Review Memory MENU 2/3 0. 0 1sec. [. . . ] 119 Movie SR (Movie Shake Reduction) Function . . . . . . . . 122 Multi-segment metering L . . . . . . . . . . . . . . . . . . . . . 109 9 Appendix 248 N Natural Skin Tone Mode . . . . 81 Night Scene Portrait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]